manualshive.com logo in svg

Laser Dollhouse Designs Stansfield Victorian Dollhouse, Assembly Instructions Manual

Share
Download
Laser Dollhouse Designs Stansfield Victorian Dollhouse Assembly Instructions Manual Download Page 3

Pre-Assembly Parts

Interior Doors  

Figure 1

Step 1. Locate the package with the interior doors, remove items. You should have:
1-Single Arched interior door
1-Door stop (

NOT IN 1:48 scale

)

1-outer frame rail with holes for door stop (No holes in 1:48)
1-interior frame rail
1-upper and 1 lower cross frame rails.
2-Frames
You will need 220 grit sand paper for the assemble for cleaning doors.. 
SEE FIGURE 1. 

Step 2. Glue the door stop into outer frame rail as seen in Figure 2. If doing 1:48 
scale go to next step as there is no door stop) 

Step 3. Glue the top cross rail to the top of the outer frame, make sure the hole is on 
the left side. This is where the door hinge will be inserted. See figure 3. 

Complete steps 1 thru 3 for remaining 3 door. You should have 4 half door 
assemblies as seen in figure 4.

Figure 3

Figure 4

Figure 2

Summary of Contents for Stansfield Victorian Dollhouse



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands