manualshive.com logo in svg

Laser Dollhouse Designs Stansfield Victorian Dollhouse, Assembly Instructions Manual

Share
Download
Laser Dollhouse Designs Stansfield Victorian Dollhouse Assembly Instructions Manual Download Page 7

Pre-Assembly Parts

Main Door

Figure 5

Figure 7

Figure 6

Step 3. Locate main door (fig, 5) and sand front and back of doors using 220 grit 
sand paper. Do this by laying door flat on top of sand paper on a flat surface. Next 
press down with slight pressure moving door side to side. We are only looking to 
clean door for painting later so do not over sand. Complete this for the outer lattice 
frame as well, be gentle not to break it. 

Step 4. Using wood glue, glue the lattice frame to the main door frame as seen in 
figure 6. 

Do NOT use supper glue!!!

Step 5. Once glue dries sand frames on all side to ensure that door is square with 
installed lattice. 

DO NOT OVER SAND EDGES… Use slight pressure. If all sides are 

aligned there is no need to sand down… 

Step 6. Using the same steps for the interior doors, assemble door frame and place 
into Main Frame assemble to dry. (Fig. 8).
Make sure opening is to the back when inserting door as this is where the glass will 
go once painted…
Next when glue dries remove and glue main frame to door assemble. (Fig.9) 
Main Door assembly complete !!!!

Figure 8

Figure 9

Summary of Contents for Stansfield Victorian Dollhouse



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands