Lantronix SCS100 Page 44 User Manual Download

Page: 44 / 62

SCS100/200/400 User Guide

6: Application Setup

Configuring an Email Site

Click the

Update

button to save changes.

Dial-Out ISP Connection

In some cases, you may require the SCS to connect to an ISP to access email or the
Internet. You can configure the SCS to automatically connect to an ISP and accept a
dynamically assigned IP address from the ISP.

When you configure a dial-out ISP connection using the web browser interface, a site
named

outgoing

is created. Once the site is properly configured, outbound packets

should cause the site

outgoing

to start and dial out using the modem.

Configure a modem to handle connections from the SCS as described earlier.

Click the

Dial-Out

link under Quick Setup.

Complete the following fields:

a) The

Remote Username

and

Password

for the ISP.

b) The

Port

that the modem is attached to (for a PC card modem, enter port 3).

c) The

ISP's

Telephone

number.

d) If necessary, a static

IP Address

Note:

Most ISPs assign a dynamic IP address. Set the IP address

field on the web page to DYNAMIC for this situation.

Specify a Nameserver.

6-14

Summary of Contents for SCS100































































Search results

Summary of Contents for SCS100

Reviews:

Related manuals for SCS100

Brands by name

Popular brands

Lantronix SCS100, User Manual

Search results

Summary of Contents for SCS100

Reviews:

Related manuals for SCS100

Brands by name

Popular brands