OPERATION AND MAINTENANCE
DANGER
NEVER ALLOW ANYONE TO RIDE ON
THE 875 SERIES TILLOLL AT ANY
TIME. ALLOWING A PERSON TO RIDE
ON THE MACHINE CAN INFLICT SERI-
OUS PERSONAL INJURY OR DEATH
TO THAT PERSON.
DANGER
DISC BLADES ARE EXTREMELY
SHARP. EXERCISE EXTREME CARE
WHEN WORKING ON OR NEAR DISC
BLADES. DO NOT ALLOW DISCS TO
ROLL OVER OR FALL ONTO ANY BOD-
ILY
PART.
DO
NOT
ALLOW
WRENCHES TO SLIP WHEN WORKING
NEAR DISC BLADES. NEVER PUSH
WRENCHES TOWARD DISC BLADES.
DO NOT CLIMB OVER MACHINE
ABOVE DISC BLADES. FAILURE TO
STAY CLEAR OF DISC BLADE EDGES
CAN CAUSE SERIOUS PERSONAL IN-
JURY OR DEATH.
DANGER
STAND CLEAR OF WINGS WHILE
FOLDING OR UNFOLDING. ALL HY-
DRAULICALLY ELEVATED EQUIP-
MENT MUST HAVE CYLINDER LOCK-
OUTS INSTALLED OR BE LOWERED
TO THE GROUND, WHEN SERVICING
OR WHEN EQUIPMENT IS IDLE. FAIL-
URE TO TAKE PREVENTIVE MEAS-
URES AGAINST ACCIDENTAL LOWER-
ING CAN RESULT IN SERIOUS PER-
SONAL INJURY.
DANGER
ALWAYS LOCK THE TRACTOR DRAW-
BAR IN THE CENTER POSITION WHEN
TRANSPORTING THE UNIT. FAILURE
TO DO SO CAN RESULT IN SERIOUS
INJURY OR DEATH AND CAUSE DAM-
AGE TO THE EQUIPMENT.
DANGER
WHEN TRANSPORTING THE UNIT,
PLACE CYLINDER LOCKOUTS IN THE
TRANSPORT LOCK POSITION AFTER
FULLY EXTENDING THE CYLINDERS.
INSERT THE LOCKOUT PINS TO SE-
CURE THE CYLINDER LOCKOUTS.
FAILURE TO LOCKOUT THE CYLIN-
DERS CAN CAUSE THE UNIT TO SET-
TLE DURING TRANSPORT, WHICH
CAN RESULT IN SERIOUS INJURY OR
DEATH AND CAUSE DAMAGE TO THE
EQUIPMENT.
CAUTION
WHEN TRANSPORTING FARM IMPLE-
MENTS ON PUBLIC ROADS, IT IS THE
RESPONSIBILITY OF THE OPERATOR
TO ABIDE BY STATE AND LOCAL
LAWS CONCERNING WIDE LOADS,
SPEED, SAFETY EMBLEMS AND
SAFETY LIGHTING EQUIPMENT.
DRIVE AT SAFE SPEEDS. PARTICU-
LARLY WHEN ROUNDING CORNERS,
CROSSING ROUGH GROUND OR
DRIVING ON HILLSIDES, TO PREVENT
TIPPING THE TRACTOR.
4-1
Summary of Contents for 875-18
