background image

OPERATION AND MAINTENANCE

4-23

Dry Fertilizer Combination Box

1.

If the Grain Drill is equipped with the dry fertilizer 
option, it will have a combination seed/fertilizer box. 
The seed/fertilizer box is split for approximately 60% 
(2 bu/ft) seed and 40% (1.25 bu/ft) fertilizer. The box 
may be used for applying both seed and fertilizer, or 
converted to use both compartments entirely for 
seed.

a.

To use the dry fertilizer option, the covers in the 
bottom of the rear fertilizer compartment must 
have the openings to the rear 

(See Figure 4-22.)

 

This will close off openings to the seed 
compartment and allow dry fertilizer to enter the 
fertilizer meters.

b.

For increased seed capacity and non fertilizer 
use, the covers should be reversed with the 
openings to the front of the seed box, and the 
solid portion covering the fertilizer meters 

(See 

Figure 4-23.)

2.

To change the fertilizer covers, remove the plastic 
knobs holding each of the covers in place at the 
bottom of the rear fertilizer compartment. Lift the 
cover out, and reposition the cover with the openings 
to the front or rear as desired. Insure the cover is slid 
down to the bottom and reinstall the plastic knobs to 
retain the covers.

Figure 4-22: Top View of Fertilizer Box w/ Cover 

Openings to Rear

Figure 4-23: Top View of Fertilizer Box w/ Cover 

Openings Forward

fertbox opening - rear

FRONT OF SEED BOX

FERTILIZER OPENINGS 
TO REAR

FRONT OF SEED BOX

FERTILIZER OPENINGS IN
FORWARD POSITION

fertbox opening - forward

Summary of Contents for 5530







































































Reviews: