background image

Section 1: Assembly & Set-up 

MR1572 & HR2572

 Retractable Box Scraper 305-083M

11/28/18

8

Table of Contents

3-Point Hook-up

Refer to Figure 1-4:

DANGER

!

To avoid serious injury or death:  

A crushing hazard exists while hooking-up and unhooking 

implement. Keep people and animals away while backing-

up to implement or pulling away from implement. Do not 

operate hydraulic controls while a person or animal is 

directly behind the power machine or near the implement.

Relieve all hydraulic pressure before disconnecting any 

lines or pipes between implement and tractor hydraulic 

system.

A 3-point Category I hitch is required. The lower 3-point 
arms of the 3-point hitch must be stabilized to prevent 
side-to-side movement. Most tractors have sway blocks 
or adjustable chains for this purpose.

1.

Slowly back tractor up to the Box Scraper and use 
tractor’s 3-point hydraulic control to align lower hitch 
link holes with lower clevis lug holes (#8).

2. Engage tractor park brake, shut tractor engine off, 

and remove key before dismounting from tractor.

3. With tractor’s lower hitch arms aligned and 

positioned between clevises (#8), attach lower arms 
to the clevises with hitch pins (#1) and secure with 
linchpins (#2).

4. Connect top center link to upper hitch clevises (#9) 

using customer supplied hitch pin (#3) and hitch pin 
keeper (#4).

5. Return to the tractor and slowly operate the tractor's 

3-point hydraulic control lever up and down to check 
for clearance between the tires, frame, drawbar etc. 
Move or remove drawbar if it interferes with the Box 
Scraper.

NOTE:  

Land Pride’s Quick Hitch can be attached to 

the tractor to provide quick and easy 3-point hook-
up and detachment. See your nearest Land Pride 
dealer to purchase a Quick-Hitch.

6. Manually adjust one of the two lower lift arms up or 

down to level the Box Scraper from left to right. 

7.

Manually adjust the length of the top-link to level the 
Box Scraper from front to rear. 

8. Ensure that the lower arms are blocked to prevent 

excessive side movement.

HR25 Hydraulic Hook-up

WARNING

!

To avoid serious injury or death:  
Hydraulic fluid under high pressure can penetrate the skin 

and/or eyes causing a serious injury. Wear protective gloves 

and safety glasses or goggles when working with hydraulic 

systems. Use a piece of cardboard or wood rather than hands 

when searching for leaks. A doctor familiar with this type of 

injury must treat the injury within a few hours or gangrene 

may result. DO NOT DELAY.

1.

Attach hydraulic couplers (#5) (supplied by 
customer) to the end of hydraulic hoses (#6 & #7).

1.

Connect hydraulic hoses (#6 & #7) to tractor remote 
outlets.

2. Cycle hydraulic system by raising and lowering 

hydraulic cylinder several times. It may be necessary 
to purge the system of trapped air if operation 
remains sluggish. The system may be purged as 
follows:

a. With tractor shut off and the Box Scraper resting 

on the ground, loosen hydraulic hose fitting at the 
cylinder slightly to allow fluid to escape.

b. Slowly activate tractor control valve to purge any 

trapped air from the system.

c. Tighten each fitting once the system has been 

purged.

Tractor 3-Point Hook-up

Figure 1-4

37298

Summary of Contents for MR 1572



























Reviews: