background image

Section 1: Assembly & Set-up 

MR1572 & HR2572

 Retractable Box Scraper 305-083M

11/28/18

6

Table of Contents

Section 1: Assembly & Set-up

Tractor Requirements

The Retractable Box Scrapers are designed with a 
3-point category l hitch. Horsepower rating should not 
exceed the following:

HR15 & MR15  . . 40 hp for 4-wheel drive tractors

. . . . . . . . . . . . . . 50 hp for 2-wheel drive tractors

HR25 . . . . . . . . . 60 hp for 4-wheel drive tractors

. . . . . . . . . . . . . . 60 hp for 2-wheel drive tractors

WARNING

!

To avoid serious injury or death:  
Lightweight tractors with rear attached implements may need 

weights added to the front to maintain steering control. 

Consult your tractor Operator’s Manual to determine proper 

weight requirements and maximum weight limitations.

MR15 Dealer Assembly

Figure 1-1

23754

Shank Tube

Remove shipping hardware (#1 & #2) after 
blocking shank tube up.

Torque Requirements

Refer to 

“Torque Values Chart”

 on page 20 t

determine correct torque values when tightening 
hardware. 

MR15 Dealer Assembly

Refer to Figure 1-1:

WARNING

!

To avoid serious injury or death:  
Before removing shipping hardware, support underside of 

shank tube with blocking near the pivot bracket to prevent Box 

Scraper from tipping forward and causing bodily injury.

1.

Support underside of shank tube with blocking before 
removing bolt (#2) and to prevent unit from tipping 
forward while setting-up the Box Scraper.

2. Remove shipping bolt (#2) and nut (#1) from pivot 

bracket.

3. Insert retractable handle (#5) through hole “A” in top 

of pivot bracket.

4. Attach pin tube (#3) to retractable handle (#5) with 

1/4"-20 x 1 1/2" GR5 hex head cap screw (#6) and 
hex nylock nut (#7). Make sure cotter pin hole is on 
the spiring side of the handle as show. Tighten nut to 
the correct torque.

5. Insert retract pin (#4) through hole at end of pivot 

bracket, compression spring (#10), 1/2" flat 
washer (#8), pin tube (#3), and out through hole on 
far side of pivot bracket.

6. Insert hair pin cotter (#9) through pin tube (#3).

Summary of Contents for MR 1572



























Reviews: