background image

11

8/15/05

    Manual No. 701-055M

Land Pride

Assembly Instructions for ST & NT Trekers (S/N 418338-)

Assembly Instructions for
ST & NT Trekers (S/N 418338-)

On page 15 is a detailed listing of parts included in this
kit. Use this list as a checklist to inventory parts received.

The pictures in this section are of an NT Series Treker
unless stated otherwise. Battery location and main wiring
harness will be in a slightly different location for the ST
Series.

Tools required:

Standard Blade Screwdriver

Needle Nose Pliers

Work Gloves

Initial Preparations

!

WARNING!

The Electric Bed Lift wiring harness should be installed as
outlined in these instructions before removing the Bed
Latch Lock-Up Arm to prevent possible injury while
working under the cargo box.

1.

Park vehicle on a flat surface, move gear shift lever to
neutral, set park brake, turn off engine and remove
ignition key.

Refer to Figure 1C:
2.

Raise the cargo box fully up to support it with the Bed
Latch Lock-Up Arm.

Bed Latch Lock-Up Arm

Figure 1C

21173

Bed Latch

Lock-Up Arm

Refer to Figure 2C:
3.

Unbolt and remove bed latch lock-down from the
driver’s side of chassis.

Bed Latch Lock-Down

Figure 2C

Wiring Harness Installation

!

CAUTION!

Disconnect battery before doing any electrical work. Do
not reconnect battery until Electric Bed Lift wiring harness
is completely installed. Injury to a person and/or the
vehicle may result if this caution is not followed.

Refer to Figure 3C:
1.

First disconnect the black negative lead at the
battery. Then disconnect the red positive lead. Do
not reconnect until instructed.

Battery Connection (ST Series Shown)

Figure 3C

Refer to Figure 4C on page 12:
2.

Locate the two-prong connector on the electric lift
wiring harness. Also, under the seat platform is the
vehicle’s main wiring harness where multiple
connectors are bundled together. Locate the oval
shape connector in this bundle that mates with the
two-prong connector on the electric lift wiring
harness and snap the two together.

Bed Latch

21174

Black Negative

Connection

Red Positive

Connection

21185

Summary of Contents for Land Pride Automobile Accessories 4200

















Reviews: