background image

9

 

Each brand has a default water type and ratio already 

set when they are selected. The water type and ratio 

can be adjusted if necessary, however, adjusting the  

ratio here is purely representational and does not 

set the ratio for the finished drink. Adjust the ratio by 

selecting the Ice or No Ice ratio using the buttons in the 

upper right corner of the screen, or by manually  

adjusting the ratio by tapping the number and entering 

the new value on the keypad. 

NOTE

6. 

Once a brand/flavor has been selected to a corresponding 

module, press the 

Valve Configuration

 button to return to the 

Valve Configuration Screen.

7. 

Repeat Steps 4 and 5 for any of the other brand or flavor 

modules. 

8.  Press the Menu button to return to the Service menu.

12.  Press the Menu button to return to the Service Menu.
13. 

Repeat steps 1 - 12 for the second screen.

9.  From the Service Menu, press the Maintenance button.
10.  Press the Purge tab on the far left side of the screen. 
11. 

Purge any new brand or flavor module until there is a steady 

flow of syrup. (See previous page)  

CALIBRATION & MAINTENANCE

Calibrating Plain/Carbonated Water Modules

1.  Access the Service menu (See page 7) and press the  

Maintenance

 button.

2.  Remove the two thumb screws connecting the plastic screen 

housing to the unit.

3.  While holding the plastic screen housing, tilt the housing 

forward until the housing disengages from the unit. 

A

B

A. Screen Housing

B. Thumb Screw

A

A. Tilt Screen Housing

Summary of Contents for Twin Pour





















Reviews: