background image

Explanation of the operating elements  

Operation

 

 

Operation 

Explanation of the operating elements 

Selection switch 

RUN Automatic 

mode 

i

  

Standby (frost protection only) 
burner OFF, pump OFF 

W

Service 1 / Emerg-Mode (set value => °C

D

Burner ON, Pump ON*) 
Modulation: Burner On, Air damper CLOSE 

W

1 + Prog button => Relay Test (=>Rotary knob) 

W

Service 2 / Emerg-Mode (set value => °C

D

   

H

 1/2/11/Mod = 2: Burner 1+2 ON, HS1 Pump ON*) 

   

H

 1/2/11/Mod = 11: Burner 2 ON, HS2 pump ON*) 

   

H

 1/2/11/Mod = m: Burner ON, Air damper OPEN  

BUS ID 

bus identification (boiler number) 

°C

D

 

in the case of fixed value: Flow / Return flow set 

 

temperature in the case of control mode: 

 

Maximum flow temperature 

 

with cascade: Presettings via cascade 

controller 
°C 

F

 without 

function 

v

 

b

  

in the case of return flow temperature increase 

 

using mixer:  

  

Mixer dynamics [K for 100% control] 

 

Modulation in cascade: Air damper activation 

 time 

[s] 

°C 

D

  

in the case of return flow temperature increase: 

 

min. return flow temperature 

H

 1/2/11/Mod  

heat generator stages  

(1=single stage, 2=two-stage, 11=2HS, m=modulating) 
*) Pump ON > [°C

D

+5K v 65°C]; OFF < [°C

D

-5K v 

55°C] 

 

Rotary knob 

  Adjusting a set value 

 

Button STL-test / Enter / Reset 

STL-test (RT without effect) => By pressing > 1s 
=>Burner on, for as long as button is pressed, display: HS-
Temp flashes (no function as mixer) 

 

Enter (modify set values) => Selection of parameter for 
adjustment (flashing); Save by pressing again 
=> for temperature readouts: Display set value (for 2 
seconds)  

 

Reset: In order to reset the controller to the default setting, 
keep the button pressed while defining the operating 
voltage (display "

EE

") All user values will be lost during this 

procedure! For this reason, please take a note of your own 
parameters in this manual. 

Settings via DIP switch (rear side) 

1:  

no function in V1 

2: 

no function in V1 

3: 

no function in V1 

4: 

no function in V1 

5: 

no function in V1 

6: 

Sensor selection: 5K NTC <-> 1K PTC 

Summary of Contents for Basic 0201 R V1

















Reviews: