background image

All wiring must conform to local and national electrical
codes and ordinances.

This control is a precision instrument, and should be
handled carefully. Rough handling or distorting compo-
nents could cause the control to malfunction.

To prevent electrical shock and/or equipment
damage, disconnect electric power to system at
main fuse or circuit breaker box until installation
is complete.

Do not use on circuits exceeding specified volt-
age. Higher voltage will damage control and
could cause shock or fire hazard.

Do not short out terminals on gas valve or pri-
mary control to test. Short or incorrect wiring will
burn out thermostat and could cause personal
injury and/or property damage.

Operator: Save these instructions for future use!

PART NO. 37-5093B

Replaces 37-5093A

9531

FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY
BEFORE INSTALLING OR OPERATING THIS CONTROL COULD CAUSE
PERSONAL INJURY AND/OR PROPERTY DAMAGE.

INSTALLATION INSTRUCTIONS

1F97W-51

 7-Day  Electronic Digital Thermostat

WHITE-RODGERS DIVISION
EMERSON ELECTRIC CO.
9797 REAVIS ROAD
ST. LOUIS, MISSOURI  63123-5398

Printed in U.S.A.

R

CONTENTS

Description .........................................................  1
Precautions ........................................................  1
Specifications .....................................................  2
Installation ..........................................................  2

New Installation

Select Thermostat Location
Route Wires to Location

Replacement Installation

Remove Old Thermostat
Attach Subbase to Wall
Attach Thermostat to Subbase

Operation ...........................................................  6

System Configuration

Electric Heat Systems
Energy Management Recovery (EMR)

Check Thermostat Operation

Fan Operation
Heating System
Cooling System

Troubleshooting

WHITE-RODGERS

This wall-mounted, low voltage thermostat maintains
room temperature by controlling the operation of heating
and cooling systems. The user may program up to four
time/temperature settings per 24 hour period. The ther-
mostat stores independent heating and cooling programs
for each day of the week. The thermostat will store both
heating and cooling programs simultaneously. Three
“AA” Energizer

®

 batteries will maintain the stored program

for approximately one year, if incoming power should fail.
If power failure is extensive and the program is lost, after
power restoration, the thermostat will automatically main-
tain a factory preprogrammed heating temperature of
64

°

F or a cooling temperature of 82

°

F.

DESCRIPTION

PRECAUTIONS

If in doubt about whether your wiring is millivolt, line, or low
voltage, have it inspected by a qualified heating and air
conditioning contractor, electrician, or someone familiar
with basic electricity and wiring.

Do not exceed the specification ratings.

CAUTION

!

WARNING

!

Summary of Contents for 1F97W-51









Reviews: