background image

General information

 

Assembly / Dismantling

 

15 

 

Sensor values / characteristic curve 

 

Temperature  5Kohm NTC 

1Kohm PTC 

-60°C 

698961 

 470 

 

-50°C 

333908 

 520 

 

-40°C 

167835 

 573 

 

-30°C 

88340 

 630 

 

-20°C 

48487 

 690 

 

-10°C 

27648 

 755 

 

0°C 

16325 

 823 

 

10°C 

9952 

 895 

 

20°C 

6247 

 971 

 

25°C 

5000 

 1010 

 

30°C 

4028 

 1050 

 

40°C 

2662 

 1134 

 

50°C 

1801 

 1221 

 

60°C 

1244 

 1312 

 

70°C 

876 

 1406 

 

80°C 

628 

 1505 

 

90°C 

458 

 1607 

 

100°C 

339 

 1713 

 

110°C 

255 

 1823 

 

120°C 

194 

 1936 

 

 

 

 

Errors 

When there is an error, the corresponding error number 
flashes. 

 

Resetting error number 81: 
Switch mains voltage Off and On again.  

 

Error no.  Error description 
Communication error 

E 91 

Bus ID used. The set bus ID is already in use 
by another device. 

Internal error 

E 81 

EEPROM error. The invalid value has been 
replaced with the default value 

E

 Check parameter values! 

Sensor defective (break/short circuit) 

E 70 

Flow sensor 

E 75 

Outdoor sensor 

E 76 

Storage tank sensor 

E 77 

Boiler sensor 

E 80 

Room sensor 

Summary of Contents for Basic 0201 R V1

















Reviews: