background image

59

27) EN-RF1 RADIO RECEIVER

1 - GENERAL INFORMATION

The single-channel receiver EN-RF1 is a 433.92 MHz radio receiver designed to open the automatic door NEPTIS PLUS using the 

transmitters manufactured by Label. 

In Table 1 there is a list of radio transmitters produced by LABELSpa.

2 - DESIGNED USE

The  receiver  EN-RF1  must  be  coupled  to  the  connector  J12  of  the  logic  card  LCB  and  it  is  intended  to  control  the  opening  of  the 

automatic door in all the work programs of the automation.

WARNING:

The opening command of the automatic door is issued by the radio control, but movement protection and safety are delegated to organs 

other than the receiver.

It  shall  never  be  used  in  any  case  where  the  door  activation  or  deactivation  may  cause  injuries  and  damage.  Receiver  in  class  3 

according to the standards ETSI EN 300-220-2 V.3.1.1 (2016-11).

3 - INSTALLATION OF THE RECEIVER

Plug the EN-RF1 receiver (fig. 1) into the J12 connector of the LCB logic card of the automation (fig. 2). Proceed with saving the radio-

controls (fig.3) as follows:

a)  Enter the programming mode of the transmitters pressing and holding the button SW1 until the LED L1 

 is steadily lit (approx. 3 

seconds).

b)  Press the button of the transmitter to be saved. Successful saving will be indicated by 5 fast flashings of the LED L1 

.

c)   Then LED L1 will turn on steadily again and it will be possible to save another transmitter by repeating the operation described in 

point b), and so forth for all the transmitters to be used.

 • 

A maximum of 250 transmitters can be saved on the receiver.

d)  Once the transmitter saving procedure is finished, exit the programming mode by pressing and holding the button SW1 until the LED 

L1 (

) turns off.

4 - USE OF THE RADIO CONTROL

By pressing the button of a saved transmitter, the automatic door opens and the LED L1 of the receiver remains on until the button of the 

transmitter is released.

The radio control opens the door in all the operating programs of the automation.

5 - RECEIVER MEMORY ERASURE

Should it be necessary to erase all the transmitter codes saved in the memory of the receiver EN-RF1, proceed as follows:

a)  Extract the EN-RF1 receiver from the J12 connector of the LCB logic card.

b)  Hold the receiver SW1 button pressed and simultaneously insert the EN-RF1 receiver into the J12 connector of the LCB logic card.

c)  Release the button SW1 from the receiver EN-RF1 only after the LED L1 of the receiver starts flashing.

  Now the LED L1 of EN-RF1 blinks fast 

  to indicate that the receiver is ready to save the codes of all the transmitters of the LABEL 

range, both rolling code models and dip switch models.

  If you only wish to save the rolling code transmitters (SPYCO model), excluding all dip switch models, briefly push the SW1 button; 

the LED L1 blinks slowly 

 to indicate that the receiver is ready to save only the SPYCO transmitter codes.

  To switch from one mode to the other, press the button SW1.

d)  After selecting the desired mode, press and hold the button SW1 for about 3 seconds until the LED L1 

 begins blinking very fast 

for about 8 seconds, signalling that the receiver memory is being erased.

e)  When the memory of the receiver EN-RF1 has been erased, the LED L1 will turn off.

f)  Now it is possible to save again the code of the transmitters to be used, following the procedure described in paragraph 3.

6 - TECHNICAL SPECIFICATIONS

Power supply  

12Vdc

Power draw  

10mA at rest - 50mA in operation

Outputs  

OPEN COLLECTOR

Frequency 

433.92 Mhz

Memory Capacity  

250 users

Range without obstacles  

30 meters

Operating temperature  

-20° / +55°

Receiver class (ETSI EN 300-220-1 Chapter 4.1.1)  

Class 3

7 - DECLARATIONS

Marketing, sale and use are valid without restrictions in all EU countries.

With this document Label SpA declares that the receiver EN-RF1 complies with all the essential requirements and with all other relevant 

provisions established by the directive RED 2014/53/EC.

The declaration of conformity is annexed to the instructions of the receiver EN-RF1.

Summary of Contents for NEPTIS PLUS





































































Reviews: