background image

20

9) NEPTIS PLUS AUTOMATIONS WITH BATTERY (SLTB, LETB, SMTB MODELS)

This type of automation has a built-on NB-BAT battery module, designed to ensure that the automation keeps running when no power 

supply is available.

Location of the NB-BAT module inside the Neptis Plus automation.

The location of the NB-BAT module inside the automation depends on the type of arm in use. 

When using the BDT2, BDT2R55 or BDT2R90 slide pull arm and the BSG elbow arm, the NB-BAT module must be next to the PWB 

power supply unit (FIG.1).

When using the BSS2 articulated push arm and the BDS slide push arm, the N-BAT module must be next to the gearmotor (FIG. 2).

Label provides as standard the Neptis Plus automation with NB-BAT 

module installed on the gearmotor side, and thus set up for push 

opening (FIG.3).

     

          

If you must use a BDT2, BDT2R55 or BSG arm for pull opening, 

you will have to move the NB-BAT module to the opposite side, 

performing the following operations:

a) Disconnect the connection cable between the J1 connector of the 

NB-BAT module and the J3 connector of the PWB power supply, 

than cut the straps holding it fastened to the mechanical body of 

the automation;

b) Remove the plastic side caps from the automation by unscrewing 

the relevant screws;

c) Detach the NB-BAT module from the Neptis Plus automation, 

unscrewing  the  M6X8  screws  fixing  the  coupling  plates  (P) 

between the two parts;

d) Place the NB-BAT module on the side of the PWB power supply 

unit, inserting the coupling plates (P) into the special grooves and 

screwing in the M6x8 screws (FIG.4);

The automation is now ready to be used with the pulling arm (FIG.5).

e)  Reinstall the plastic side caps to the side of the automation.

NOTE

: for information about the automation installation dimensions, 

please  refer  to  the  technical  drawings  in  paragraph  5,  taking  into 

account that the battery module is always on the side opposite to 

the door pivots.

The automation's cover is equipped with a double slot, so that it can 

be installed on both sides, depending on the position of the NB-BAT 

module inside the automation.

For information on the electrical connection and the operation, 

please refer to the paragraph "NB-BAT BATTERY MODULE" in the 

"ELECTRONICS" section

GEARMOTOR

NB-BAT

PWB

GEARMOTOR

PWB

NB-BAT

PWB

NB-BAT

GEARMOTOR

PWB

NB-BAT

GEARMOTOR

P

M6x8

FIG.1

FIG.2

FIG.3

FIG.4

FIG.5

Summary of Contents for NEPTIS PLUS





































































Reviews: