background image

46

• 

You are prompted to repeat the new password, so enter again the previous combination.

• 

If  the  password  entered  is  correct,  the  message  “PASSWORD  OK”  is  displayed  for  one 

second, then the system returns to the PASSWORD MANAGEMENT section. Press the EXIT 

 button to return to the general programming menu

• 

If the password you entered does not match the previous one, the display shows PASSWORD 

ERROR, the system returns to the section PASSWORD MANAGEMENT and it is necessary to 

perform again the procedure.

• 

Enter the primary password 

• 

Enter the new service password, selecting a combination of 5 characters from the letters A-B-

C-D.

• 

You are prompted to repeat the new password, so enter again the previous combination.

• 

If  the  password  entered  is  correct,  “PASSWORD  OK”  is  displayed  for  one  second  and  the 

system returns to the PASSWORD MANAGEMENT section.

21.3) HOW TO CHANGE THE SERVICE PASSWORD

• 

Select “SERVICE PASSWORD”

• 

Press OK (F1).

Press the EXIT 

 

 button to return to the general programming menu.

If the password you entered does not match the previous one, the display shows PASSWORD ERROR, the system returns to the section 

PASSWORD MANAGEMENT, and it is necessary to perform again the procedure.

Summary of Contents for NEPTIS PLUS





































































Reviews: