background image

Page 40

9.E 

System Shutdown

1.  Turn off the main electrical disconnect switch.

2.  Close all manual gas valves.

3.  These boilers are certified for indoor use only and should not be subjected to 

freezing temperatures. When shutdown or during and extended power outage, 

component failure or other condition when freezing is likely, the boiler and 

system must be drained.

 

To completely drain the boiler, 

 

• 

First drain the right side by opening the boiler drain. 

 

• 

Remove the PRV and related fittings. 

 

• 

Remove the top and left side panels. 

 

• 

 Remove BOTH 1/2” plugs from the side of the boiler located at the 

bottom of the casting. Once the water is fully drained, reinstall the 

plugs and panels. See 10.A.3 

4.   Be sure to protect the piping in the building from freezing.

 

 

WARNING

This step must be performed by 

 a qualified service technician.

 

SECTION 10 

MAINTENANCE

10.A  Removing the covers and panels

 

WARNING

 

Do not leave this panel off in normal operation.  

 

High voltage and temperatures could cause a 

hazardous condition 

10.A.1 

Access Cover Removal  

To remove the front access cover simply turn the lock at the top 

center of the panel with a flat screw driver (slot indicates locking 

arm direction). Lift slightly and tip the top of the panel forward. 

Reverse the process to reinstall. 

10.A.2 

Flue Collector Access 

After removing the front access cover, the top access panel can 

then be lifted up and off the unit.  This will expose the flue collector.  

Lift the flue collector using the handle in the front and slide it up 

and out.  This will allow access to the top of the heat exchanger for 

cleaning.  

Re-install the flue collector in reverse order, 

ensuring that the 

front tabs contact the castings and the bottom flange 

are inserted into the front heat exchanger baffle.

  Return 

the top panel by inserting the rear edge first at approximately a 

15-degree angle then dropping the front.  There is a slight spring 

force pushing forward.

Figure 47. 

  Remove the Front Cover

Figure 48.   Lift Flue Collector Up and Out

 

LAARS Heating Systems

Summary of Contents for MINI-THERM JX





















































Reviews: