⚵┙ߡ೨ߩᵈᗧ㧔㧞㧕
BEFORE YOU BEGIN (2)
5
62ࡆࠬߪޔㇱຠߦࡀࠫࠍಾࠅߥ߇ࠄߒߟߌࠆࡆࠬߢߔޕߒߎߺ߇࿕႐ว߇
ࠅ߹ߔ߇ޔㇱຠ߇⏕ታߦ࿕ቯߐࠇࠆ߹ߢߒߎࠎߢߊߛߐޕߚߛߒޔߒߔ
߉ࠆߣࡀࠫ߇߈߆ߥߊߥࠅ߹ߔߩߢޔㇱຠ߇ᄌᒻߔࠆ߹ߢߒߥߢߊߛߐޕ
Self-tapping (TP) screws cut threads into the parts when being tightened. Excessive force may
permanently damage parts when tightening TP screws. It is recommended to stop tightening when
the part is attached or when some resistance is felt after the threaded portion enters the plastic.
7
ࡆࠬ߇߈߆ߥ
The threads are stripped.
ߒߔ߉
Overtightened.
Correct
Wrong
ࠠ࠶࠻ߦߪޔᒻ߿㐳ߐ߇㆑߁ࡆࠬ߿ዊ‛ㇱຠ߇ᄙߊߞߡ߹ߔޕ⺑ᦠߦߪේኸ࿑߇ࠅ߹ߔߩߢ⏕ߒߡ߆ࠄ⚵┙ߡ
ߡߊߛߐޕ߹ߚޔࡆࠬ㘃ߪᄙߦߞߡࠆ߽ߩ߽ࠅ߹ߔߩߢޔ੍ߣߒߡ߅ߊߛߐޕ
This kit contains screws and hardware in different metric sizes and shapes. Before using them, check the screws on the true-to-scale diagrams on the
left side in each assembly step. Some screws are extras.
6
٨ࡆࠬߩ⒳㘃
SCREWS
ࡆࠬ
Screw
ࠠࡖ࠶ࡊࡆࠬ
Cap Screw
TP
ࡆࠬ
Self-tapping (TP) Screw
TP
ࠨࡆࠬ
TP F/H Screw
࠶࠻ࡆࠬ
Set Screw
٨ዊ‛ㇱຠߩࠨࠗ࠭
OTHER HARDWARE
3x12mm
ࡆࠬ
Screw
3mm
12mm
ࠨࡆࠬ
Flat Head (F/H) Screw
3mm
ࡢ࠶ࠪࡖ࠽࠶࠻
Washer
Nut
3mm
5x10mm
ࡔ࠲࡞ࡌࠕࡦࠣ
Metal Bushing
Bearing
5mm
10mm
4mm
E4
㧱ࡦࠣ
E-ring
٨
6,000
ࡄ࠰࠽࡞ࡃࡦ࠼ࡕ࠾࠲ߦߟߡ
ABOUT THE "PERSONAL FREQUENCY MONITOR"
ᗲᯏߩ㘧ⴕ೨ߦޔ߁ࡃࡦ࠼ߩࠢࠬ࠲࡞ࠍ࠶࠻
ߒߡࠬࠗ࠶࠴ࠝࡦ㧍
ห৻ࡃࡦ࠼ߩ㔚ᵄࠍࠠࡖ࠶࠴
ߔࠆߣࡉࠩ㖸ߣ
LED
ߩశߢ⼊๔ޕ
Before operating your helicopter, plug the crystal of your
frequency into the Personal Fre-quency Monitor. As soon
as you switch it on, you'll know for sure through an interfe--
rence signal and LED lamps whether somebody else is on
your fre-quency or not!
PERSONAL
BAND MONITOR
40
MHZ
OFF
ON
KYOSHO
CORPORATION
No.80591
JRMSA
77
KYOSHO CORPRATION
No.80591 (40MHz)
No.80592 (72MHz)
ኾ↪ࠢࠬ࠲࡞ᄁ
Special crystals are
available at Kyosho!
ࠠ࠶࠻ౝߩㇱຠߩਛߦߪޔ⚵┙ᷣߺߩㇱຠ߇ࠅ߹ߔޕ
ᔨߩߚࡆࠬ╬ߩࠁࠆߺ߇ή߆⏕ߒߡ߆ࠄޔ⚵┙ߡ
ߡߊߛߐޕ
Inside the kit, you will find assemblies, i.e. sections that are pre-assembled
and hence consist of more than one part. To make sure these assemblies
are safely assembled, check among others their screws for looseness. Only
then, build in the assemblies.
5
