Kyocera Mita KM-1620 Operation Manual Download Page 87

Page: 87 / 124

Section 6 COPIER MANAGEMENT

6-31

Press the [OK] key.
The display will return to that of Step 2.

Inch

specifications

Metric

specifications

Low Power Mode Transition Time

Set the time interval from the time operations end to the automatic
engagement of the Low Power Mode.

Display the Default Settings Mode. (Refer to P.6-11

"Default Settings Mode Operations Procedures"

Inch

specifications

Metric

specifications

Press either the Zoom (+) or Zoom

(–)

key to display “F35”.

Inch

specifications

Metric

specifications

Press the [OK] key.

Inch

specifications

Metric

specifications

Press either the Zoom (+) key or the Zoom

(–)

key and select

an time interval from 1 minute to 240 minutes.

Inch specifications

Metric specifications

Note

The time intervals available are: 1, 5, 15, 30, 45, 60, 90,
120, 180 and 240 minutes.

Press the [OK] key.
The display will return to that of Step 2.

Inch specifications

Metric specifications

Off Mode Transition Time

Set the time interval for automatically entering Off Mode when
copying is completed or after operations have been finished.

Display the Default Settings Mode. (Refer to P.6-11

"Default Settings Mode Operations Procedures"

Inch specifications

Metric specifications

Summary of Contents for KM-1620





























































































































Search results

Summary of Contents for KM-1620

Reviews:

Related manuals for KM-1620

Brands by name

Popular brands

Kyocera Mita KM-1620, Operation Manual

Search results

Summary of Contents for KM-1620

Reviews:

Related manuals for KM-1620

Brands by name

Popular brands