Kyocera Mita KM-1620 Operation Manual Download Page 18

Page: 18 / 124

Section 2 NAMES OF PARTS

2-2

(11) Platen

Set the original here. Place the copy original face down and
align it so that it is flush against the left rear corner of the
platen.

(12) Original Size Indicator Plate

Be sure to align the original flush with this plate when setting
it.

(13) Left Cover

Open this when a copy jam occurs.

(14) Waste Toner Box
(15) Toner Container Release Lever

Use this when replacing the toner container.

(16) Toner Container
(17) Cleaning shaft

Pull this out and then press it back in after replacing the
toner container or when blemishes appear on copies.

(18) Front Cover

Open this when cleaning or replacing the toner container or
waste toner box.

(19) Power Switch

Turn this switch ON (|) before beginning copying operations.

(11)

(16)

(12)

(15)

(14)

(13)

(17)

(18)

(19)

Summary of Contents for KM-1620





























































































































Search results

Summary of Contents for KM-1620

Reviews:

Related manuals for KM-1620

Brands by name

Popular brands

Kyocera Mita KM-1620, Operation Manual

Search results

Summary of Contents for KM-1620

Reviews:

Related manuals for KM-1620

Brands by name

Popular brands