manualshive.com logo in svg

KVH Industries TracVision A5, Shop Manual, Page: 16 / 53

Share
Download
KVH Industries TracVision A5 Shop Manual Download Page 16

54-0239

TracVision A5 Shop Manual

© 2005 KVH Industries, Inc., All rights reserved.

DO NOT...

• DO NOT twist or bend the antenna frame.

• DO NOT paint the antenna without calling KVH Technical Support

first at 

1-888-584-5714

. Painting the antenna with certain types of

paint will reduce satellite signal reception.

• DO NOT use KVH’s roof-mount kit if the roof is greater than 

3

/

16

"

thick.

• DO NOT install the antenna on an 18-wheel, commercial truck.

The excessive vibration experienced on these vehicles will impair
the antenna’s ability to track the satellite.

• DO NOT mount the antenna sideways on the vehicle’s roof. Be

sure the connector is facing the rear of the vehicle. The front of
the antenna is aerodynamically designed for the least noise and
best moisture protection.

• DO NOT use abrasive cleaners, volatile solvents (such as methyl

alcohol), or compounds that react with plastic when cleaning the
antenna.

Do’s and Don’ts - Antenna (cont’d)

Effective April 2005
Subject to change without notice

Summary of Contents for TracVision A5






















































Reviews:

No comments