manualshive.com logo in svg

KVH Industries TracVision A5, Shop Manual, Page: 15 / 53

Share
Download
KVH Industries TracVision A5 Shop Manual Download Page 15

54-0239

TracVision A5 Shop Manual

© 2005 KVH Industries, Inc., All rights reserved.

DO...

• DO remove all 6 wire shipping restraints.

• DO get another person’s help to lift the antenna.

• DO install all three TORX screws at each mounting bracket.

• DO apply threadlocker (Loctite 425) to the threads of the mounting

screws if you are reusing them.

Be careful not to drip threadlocker

on the vehicle.

• DO allow at least 1" clearance between antenna and roof.

• DO make sure the antenna is securely attached to the vehicle.

• DO make sure the roof rack crossbars are securely fastened to

the vehicle, if you are mounting the antenna to the roof rack.

• DO inform the customer of the vehicle’s height with the antenna

installed.

• DO call KVH Technical Support at 

1-888-584-5714

before you

paint the antenna. Certain types of paint will affect reception.

DO NOT...

• DO NOT attempt to lift the antenna by yourself.

• DO NOT use any substitute mounting hardware.

• DO NOT mount the antenna to a sloped surface.

Do’s and Don’ts - Antenna

Effective April 2005
Subject to change without notice

Summary of Contents for TracVision A5






















































Reviews:

No comments