Kverneland 2620M Manual Download Page 27 | Manualshive

Page: 27 / 47

background image

27

Lubrication points

Lubrication points

Every day;

PTO shaft and bevel gear;

•

Press the nozzle of the grease gun onto the grease nipple.

•

Pump 1, max. 2 times with the grease gun.

Every 40 hours;

Bushing;

•

Press the nozzle of the grease gun onto the grease nipple.

•

Pump 1, max. 2 times with the grease gun.

Spindle;

•

pump the oil can once or twice, but no more than three times.

Maintenance

«
...
25
26
27
28
29
...
»

Summary of Contents for 2620M
















































Reviews:

No comments

Related manuals for 2620M

Brand: Landoll Pages: 52

Brand: JBSYSTEMS Light Pages: 14

Brand: YardShape Pages: 50

Brand: iFIT Pages: 11

Brand: Raytheon Pages: 68

Brand: KegLand Pages: 23

Brand: Waterpik Pages: 2

Brand: WaterUps Pages: 2

Brand: L-Acoustics Pages: 5

Monkey Jump MM00125

Brand: M&M Pages: 2

Brand: Major tech Pages: 12

Brand: ebm-papst Pages: 10

CEAG Exit Cube 33822 LED CGLine+

Brand: Eaton Pages: 20

Brand: swamp Pages: 5

Brand: Kongsberg Pages: 188

Brand: Proactive Pages: 14

Brand: sauter Pages: 5

Brand: Trigano Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands