Kverneland 2620M Manual Download | Manualshive

Page: 22 / 47

background image

22

Parking / disconnection of the
machine

Parking / disconnection of the
machine

Parking / disconnection of the
machine

Parking / disconnection of the
machine

Parking / disconnection of the
machine

Parking / disconnection of the
machine

Parking / disconnection of the
machine

Parking / disconnection of the
machine

Park the machine in the
working position The machine
should always be parked in the
working position. This prevents
the machine from tipping over
and causing serious accidents.
If the machine tips over, it can
result in serious or even fatal
injuries.

•

Lower the machine's cutting
unit back down to the working
position.

•

It is recommended that the
hydraulic outlet on the tractor
is in the floating position.

The machine is disconnected in
the following way:
•

Activate the tractor's
hydraulics and lift the machine
up.

•

Pull the rope to lift the
transport lock.

•

Turn the catch to the position
shown.

Assembly - attachment

«
...
20
21
22
23
24
...
»

Summary of Contents for 2620M
















































Reviews:

No comments

Related manuals for 2620M

Brand: Waterwise Pages: 12

Brand: ParaBody Pages: 38

Brand: Xoop Lighting Pages: 20

Brand: Vari Lite Pages: 132

Brand: NAD Pages: 10

Brand: Water Witch Pages: 2

Brand: Falltech Pages: 48

Brand: Farmet Pages: 102

Brand: Taylor-Wharton Pages: 25

Brand: i-CAT Pages: 96

Smart Plus PHT-35LHS

Brand: Vatech Pages: 190

Brand: Cannon Pages: 70

Brand: Sakai Pages: 31

Heart Guardian AED

Brand: Radian Pages: 36

UltraVent XS Plus 6 2/3 E

Brand: Rational Pages: 220

Brand: MacDon Pages: 558

Brand: Axi Pages: 27

Brand: AS MOTOR Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands