Kurzweil SP7 Grand Musician'S Manual Download Page 43 | Manualshive

Page: 43 / 64

background image

Dynamics

The Dynamics tab consists of Compressor, Distortion, and Bit Crusher.

Monitor Mode

Mute: Makes the monitor sound silent.
Stereo: Allows the input signal to be monitored in stereo, with input 1 for the left and input 2 for the right.
Mono: Monitors the sound in mono without dividing the input signal into L/R.

USB Rec Level

Controls the audio level being sent over USB from SP7 to your computer.

Playback Level

Controls the audio level being returned over USB from your computer to SP7

USB Loopback

When enabled, USB audio arriving at the SP7 input is fed back to the USB audio output. This can be
useful for combining backing tracks from your computer/DAW with the output from the SP7 and sending
them back to your computer for live recording/streaming.

Caution: Be sure to disable any input monitoring in your computer DAW/software to avoid feedback.

Vocal Proc. Route (Vocal Processor Route)

No Vocal Proc.: Disables all vocal processing
VP on input1: The vocal processor is applied to the Input 1 signal VP on input2: The vocal processor is

applied to the Input 2 signal

Note :

The vocal processor can only be applied to one input at a time.

4-2. Audio Input

The input section consists of Input, Dynamics (Dyn), Parametric Equalizer (P.EQ), Modulation/Wah (Mod/Wah),
Delay/Tremolo (Dly,Trm), and Mix. The dynamic (Dyn) and parametric equalizer (P.EQ) functions are the same as the
FX Bus in the Sound mode. For details, refer to [3-6. FX Bus (Zone Insert FX)] page.

Gain

: The input signal level at the input jack.

Lo-Cut

: When set to ON, it reduces the low

frequencies.

Noise Gate

: When set to ON, it reduces noise

from the input audio signal

NG Threshold (Noise Gate Threshold)

: Sets the

level at which the gate opens

NG Release (Noise Gate Release)

: Sets the

time it takes for the gate to close

Input

Chapter 4.

Audio Mode

«
...
41
42
43
44
45
...
»

Summary of Contents for SP7 Grand

































































Reviews:

No comments

Related manuals for SP7 Grand

Brand: Unex Pages: 5

Brand: GALBIATI Pages: 20

Brand: Hantek Pages: 124

Brand: Hameg Pages: 10

Brand: Jasco Pages: 2

Brand: Rath Pages: 5

HQ Power VDL25BM

Brand: Velleman Pages: 3

Brand: iGuzzini Pages: 36

AQUIS ULTRAFLOW

Brand: Waterous Pages: 56

Brand: Yamaha Pages: 48

Brand: Lalizas Pages: 12

BOBCAT 130 Series

Brand: Balcrank Pages: 12

Brand: MAGSTIM Pages: 86

Brand: JBM Pages: 13

Aristo WeldCloud Mig U5000i

Brand: ESAB Pages: 28

Brand: U.S.SAWS Pages: 21

ClusterStor H-6167

Brand: Cray Pages: 39

Elitco Lighting C202

Brand: ELEGANT Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands