KUHN FC2860TLD Operator'S Manual Download Page 8

Page: 8 / 120

FC2860TLD-3160TLD-3560TLD

3. - Identification of the machine

KN281CGB_L

Mower conditioner

3.3

Model identification plate

- Please write below the type and serial number of

the machine. This information is to be given to the
Kuhn authorized dealer for any spare parts order
or warranty claim.

• (1) The manufacturer:
• (2) Type:
• (3) Serial Number:
• (4) Weight:



According to the country of destination,

additional plates can be fitted on the
machine.

For machines aimed at countries which are
members of the European Union (EC marking):

• (5) Manufacturing year:

For machines aimed at countries member of the
Eurasian customs union (EAC marking):

• (6) Model year:
• (7) Manufacturing year:

TYPE
MASSE

KUHN S

.A.

67700 SA

VERNE

- FRA

NCE

N°

MADE IN

FRANC

TYPE
MASSE kg

KUHN S.A.

67700 SAVERNE - FRANCE

N °

MADE IN FRANCE

09993600

25: Year of Construction

0000
00/0000

26: Model Year

Summary of Contents for FC2860TLD

























































































































Search results

Summary of Contents for FC2860TLD

Reviews:

Related manuals for FC2860TLD

Brands by name

Popular brands

KUHN FC2860TLD, Operator'S Manual

Search results

Summary of Contents for FC2860TLD

Reviews:

Related manuals for FC2860TLD

Brands by name

Popular brands