KUHN FC2860TLD Operator'S Manual Download

Page: 27 / 120

4. - Safety

FC2860TLD-3160TLD-3560TLD

KN281CGB_L

Mower conditioner

4.4.2 Instructions specific to France



Speed (1)

- Always keep to the legal speed limit of 25 km/h for

driving a tractor-machine assembly on public
roads.



Coupling device

- Couple the machine to a tractor that is equipped

with a system for locking the lift arms laterally and
vertically.

- To drive on roads, respect the attachment height

specified in the operator's manual and lock the lift
linkage.

4.5

Likely critical failures

• 133993: Specific requirements for countries member of the Eurasian Economic Community (EAC

marking).

• 133994: Specific requirements for countries member of the Eurasian Economic Community (EAC

marking).

• 133995: Specific requirements for countries member of the Eurasian Economic Community (EAC

marking).

Summary of Contents for FC2860TLD

























































































































Search results

Summary of Contents for FC2860TLD

Reviews:

Related manuals for FC2860TLD

Brands by name

Popular brands

KUHN FC2860TLD, Operator'S Manual

Search results

Summary of Contents for FC2860TLD

Reviews:

Related manuals for FC2860TLD

Brands by name

Popular brands