Kubota Z723 Operator'S Manual Download

Page: 69 / 95

PERIODIC SERVICE

ENGLISH

Adjusting Choke Cable

1. Move the choke lever to the OFF position.

2. Push choke bracket in direction of arrow (A).

3. If bracket can move in direction of arrow (A), loosen

the bolt and pull the choke lever cable and sheath in
the direction of arrow (A) until bracket can no longer
move in direction of arrow (A). Then tighten the bolt.

Adjusting Throttle Cable

1. Move the throttle lever to the "FAST" position.

2. Make sure the throttle arm contacts the stopper bolt.

3. If not possible, loosen the bolt and pull the throttle

lever cable sheath in the direction of the arrow until
throttle arm contacts the stopper bolt. And then tighten
the bolt.

(1) Choke lever

(1) Choke bracket
(2) Choke bracket cable
(3) Choke bracket cable sheath
(4) Bolt

(1) Throttle lever

(1) Bolt
(2) Throttle lever cable sheath
(3) Throttle arm
(4) Stopper bolt

(P) "PULL"
(Q) "CONTACT"

Summary of Contents for Z723
































































































Search results

Summary of Contents for Z723

Reviews:

Related manuals for Z723

Brands by name

Popular brands

Kubota Z723, Operator'S Manual

Search results

Summary of Contents for Z723

Reviews:

Related manuals for Z723

Brands by name

Popular brands