Kubota Z723 Operator'S Manual Download

Page: 66 / 95

PERIODIC SERVICE

ENGLISH

Adjusting Parking Brake

To avoid serious injury:

Park the machine on a firm and level surface.

Stop the engine and chock the wheels before
checking or adjusting.

Should be serviced by your local KUBOTA
Dealer.

Wrong adjustment may cause machine damage.

(1) Check brake spring

1. Place the motion control levers to the "NEUTRAL

LOCK" position.

2. Be sure to chock the rear wheels.
3. Apply the parking brake to the lock position.
4. Check the length of the brake springs on both sides.

5. If the length of the brake spring is not correct, adjust it.

(See "Adjustment of brake spring length" in the next
page.)

6. Release the parking brake completely.
7. Hold the brake rod lightly.
8. Check the brake spring play.

9. If the brake spring play is not correct, adjust it.

(See "Adjustment of brake spring play" in the next
page.)

(A): Proper brake spring length
with the brake applied to the
lock position

114 to 115 mm

(4.49 to 4.53 in.)

(1) Brake rod
(2) Brake spring
(3) Lock nut

(A) "Parking brake spring length"

(B): Proper brake
spring play

The spring must have play.
Reference: 0.5 to 1.0 mm
(0.02 to 0.04 in.)

(1) Brake rod
(2) Brake spring
(3) Lock nut
(4) Plain washer

(A) "Hold the brake rod"
(B) "Parking brake spring play"

Summary of Contents for Z723
































































































Search results

Summary of Contents for Z723

Reviews:

Related manuals for Z723

Brands by name

Popular brands

Kubota Z723, Operator'S Manual

Search results

Summary of Contents for Z723

Reviews:

Related manuals for Z723

Brands by name

Popular brands