Kubota Z723 Operator'S Manual Download | Manualshive

Page: 29 / 95

background image

12

OPERATING THE ENGINE

ENGLISH

OPERATING THE ENGINE

To avoid serious injury:

A

Read and understand "SAFE OPERATION" in
the front of this manual.

A

Read and understand the danger, warning and
caution labels located on the machine.

A

To avoid danger of exhaust fume poisoning, do
not operate the engine in a closed building
without proper ventilation.

A

Never start the engine while standing on the
ground. Start the engine only from operator's
seat.

MOUNT AND DISMOUNT MACHINE

SAFELY

DO NOT step on either side of the mower deck when
mounting and dismounting the machine. When mounting
the machine from either side, step over the mower deck.

STARTING THE ENGINE

To apply the parking brake:

Depress the parking brake pedal firmly with the left
side of your right foot. Keeping the parking brake pedal
depressed, use the right side of your right foot to
depress the parking brake lock pedal. Then release
the parking brake pedal while holding the parking
brake lock pedal down. Then release the parking
brake lock pedal.

1. Sit on the operator's seat.

2. Apply the parking brake.

(1) Parking brake pedal
(2) Parking brake lock pedal

(A) "DEPRESS"

(1) Parking brake pedal
(2) Parking brake lock pedal
(3) Right foot

«
...
27
28
29
30
31
...
»

Summary of Contents for Z723
































































































Reviews:

No comments

Related manuals for Z723

Brand: Webb Pages: 28

Brand: Lawn Tender Pages: 16

Brand: Worldlawn Pages: 16

Brand: Pattfield Ergo Tools Pages: 80

Brand: Lawn-Boy Pages: 29

Brand: Poulan Pro Pages: 29

Brand: Walker Pages: 44

Brand: Cub Cadet Pages: 40

Brand: Craftsman Pages: 40

Brand: Craftsman Pages: 31

Brand: Craftsman Pages: 32

Brand: Craftsman Pages: 52

Brand: Craftsman Pages: 60

Brand: Craftsman Pages: 72

Brand: Craftsman Pages: 60

Brand: Craftsman Pages: 72

6.0 HORSEPOWER 22" REAR DISCHARGE ROTARY LAWN MOWER 917.387402

Brand: Craftsman Pages: 29

Brand: Craftsman Pages: 96

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands