Kubota Z723 Operator'S Manual Download

Page: 4 / 95

CONTENTS

ENGLISH

SAFE OPERATION ............................................................................................

-1

SERVICING OF MACHINE ......................................................................................... 1

SPECIFICATIONS....................................................................................................... 3

IMPLEMENT LIMITATIONS ........................................................................................ 5

INSTRUMENT PANEL AND CONTROLS................................................................... 6

MOWER MOUNTING .................................................................................................. 8

MOUNTING THE MOWER DECK ........................................................................... 8
ADJUSTING THE MOWER ................................................................................... 10
DISMOUNTING THE MOWER DECK ................................................................... 11

OPERATING THE ENGINE....................................................................................... 12

MOUNT AND DISMOUNT MACHINE SAFELY..................................................... 12
STARTING THE ENGINE ...................................................................................... 12

Throttle Lever and Choke lever ...................................................................................... 14
Key Switch...................................................................................................................... 14

CHECK DURING OPERATING ............................................................................. 15

COLD WEATHER STARTING ............................................................................... 16
WARMING UP ....................................................................................................... 16

Warm-up and Transmission Oil in the Low Temperature Range.................................... 16

JUMP STARTING .................................................................................................. 16
STOPPING THE ENGINE...................................................................................... 17

OPERATING THE MACHINE.................................................................................... 18

OPERATING NEW MACHINE ............................................................................... 18

Changing Lubricating Oil for New Machines................................................................... 18
Machine Break-in............................................................................................................ 18

OPERATING FOLDABLE ROPS ........................................................................... 19

To Fold the ROPS .......................................................................................................... 19
To Raise the ROPS to Upright Position.......................................................................... 20
Adjustment of Foldable ROPS........................................................................................ 20

STARTING ............................................................................................................. 20

STOPPING............................................................................................................. 25
PARKING ............................................................................................................... 26
TRANSPORTING................................................................................................... 26

Hydrostatic Transaxle Bypass Lever .............................................................................. 27

Summary of Contents for Z723
































































































Search results

Summary of Contents for Z723

Reviews:

Related manuals for Z723

Brands by name

Popular brands

Kubota Z723, Operator'S Manual

Search results

Summary of Contents for Z723

Reviews:

Related manuals for Z723

Brands by name

Popular brands