Kubota Z723 Operator'S Manual Download

Page: 38 / 95

OPERATING THE MACHINE

ENGLISH

How to adjust the operator's seat

Fore-aft adjustment
Pull the seat slide lever and slide the seat.

Armrest

Armrest may be set at upright position if desired.

Armrest angle adjustment

Turn the armrest angle adjustment knob to the desired
angle.

After adjusting the operator's seat, be sure to check
and see that the seat is securely locked.

Seat Belt

To avoid serious injury:

Always use the seat belt when the ROPS is
installed.

Do not use the seat belt if a foldable ROPS is
down or there is no ROPS.

Adjust the seat belt for proper fit and connect to the
buckle. The seat belt is an auto-locking retractable type.

(1) Armrest angle adjustment knob

(1) ROPS
(2) Seat belt

2. Start the engine.

See "OPERATING THE ENGINE"
section.

Summary of Contents for Z723
































































































Search results

Summary of Contents for Z723

Reviews:

Related manuals for Z723

Brands by name

Popular brands

Kubota Z723, Operator'S Manual

Search results

Summary of Contents for Z723

Reviews:

Related manuals for Z723

Brands by name

Popular brands