6-S6
L3540, L4240, L5040, L5240, L5740, WSM
FRONT AXLE
4. CHECKING AND ADJUSTING
Toe-in
1. Park the tractor on the flat place.
2. Inflate the tires to the specified pressure.
3. Turn steering wheel so front wheels are in the straight ahead
position.
4. Lower the implement, lock the parking brake and stop the engine.
5. Measure distance between tire beads at front of tire, hub height.
6. Measure distance between tire beads at rear of tire, hub height.
7. Front distance should be 2 to 8 mm (0.08 to 0.3 in.) less than rear
distance.
8. If the measurement is not within the factory specifications, adjust
by changing the tie-rod length.
Q
Adjusting
1. Detach the snap ring (3).
2. Loosen the tie-rod lock nut (1).
3. Turn the tie-rod joint (2) to adjust the rod length until the proper
toe-in measurement is obtained.
4. Retighten the tie-rod lock nut (1).
5. Attach the snap ring (3).
IMPORTANT
Q
• A right and left tie-rod joint is adjusted to the same length.
W10213280
Axial Sway of Front Wheel
1. Jack up the front side of tractor.
2. Set a dial gauge on the outside of rim.
3. Turn the wheel slowly and read the runout of rim.
4. If the measurement exceeds the factory specifications, check the
bearing, rim and front wheel hub.
W10120920
Toe-in (
(B)
-
(A)
)
Factory spec.
2 to 8 mm
0.08 to 0.3 in.
Tightening torque
Tie-rod lock nut
167 to 196 N·m
17.0 to 20.0 kgf·m
123 to 144 lbf·ft
(1) Tie-rod Lock Nut
(2) Tie-rod Joint
(3) Snap Ring
(4) Outer Tube
(A) Wheel to Wheel Distance at front
(B) Wheel to Wheel Distance at rear
(C) Front
Axial sway of front wheel
Factory spec.
Less than 5.0 mm
0.20 in.
KiSC issued 04, 2010 A
Summary of Contents for L3540
