3-S57
L3540, L4240, L5040, L5240, L5740, WSM
TRANSMISSION
Separating Mid Case
1. Lift up the shuttle shift arm (1).
2. Separate the mid case from the clutch housing after removing
their mounting screws.
(When reassembling)
• Apply liquid gasket (Three Bond 1208C or equivalent) to joint
face of clutch housing and mid case.
• When reassembling the shuttle shift arm (1) to the shuttle fork rod
(2), be sure to install it to the groove
A
.
W1018779
PTO Clutch Valve
1. Remove the PTO clutch valve (2) as a unit.
2. Pull out the pipe (1).
(When reassembling)
• Apply small amount of grease for the O-ring (3).
• Install the pipe (1) to the hole (4) of the PTO clutch valve (2)
firmly.
• Replace the pipe (1) with a new one.
W1019328
Mid Case Bearing Holder
1. Remove the PTO drive shaft (3).
2. Remove the mid case bearing holder mounting screws, and then
take out the bearing holder (2) with PTO clutch (1) as a unit.
NOTE
Q
• Take care not to fly out the ball (5) and spring (4) when pull
out the bearing holder (2).
(When reassembling)
• Tap in the mid case bearing holder (2) with plastic hummer until
contact to mid case, and then tighten the screws to specified
torque.
W1019191
Tightening torque
Clutch housing and mid
case mounting screw
78 to 90 N·m
7.9 to 9.2 kgf·m
58 to 66 lbf·ft
Clutch housing and mid
case mounting nut
103 to 117 N·m
10.5 to 12.0 kgf·m
76.0 to 86.7 lbf·ft
(1) Shuttle Shift Arm
(2) Shuttle Fork Rod
A : Fork Rod Groove
Tightening torque
PTO clutch valve mounting
screw
24 to 27 N·m
2.4 to 2.8 kgf·m
18 to 20 lbf·ft
(1) Pipe
(2) PTO Clutch Valve
(3) O-ring
(4) Hole
Tightening torque
Mid case bearing holder
mounting screw
48 to 55 N·m
4.9 to 5.7 kgf·m
36 to 41 lbf·ft
(1) PTO Clutch
(2) Mid Case Bearing Holder
(3) PTO Drive Shaft
(4) Spring
(5) Ball
KiSC issued 04, 2010 A
Summary of Contents for L3540
