8-S7
B1710 · B2110 · B2410 · B2710, WSM
HYDRAULIC SYSTEM
(2) Disassembling and Assembling
Removing Hydraulic Pump
1. Open the bonnet then remove the front grille, side cover (RH) and
disconnect the battery grounding cord.
2. Disconnect the connector of the engine stop solenoid (6) and
accelerator rod (2).
3. Disconnect the power steering delivery pipe (1) and 3-point hitch
delivery pipe (5).
4. Disconnect the suction hose (3) and remove the hydraulic pump
(4).
(When reassembling)
• Apply liquid gasket (Three Bond 1208D or equivalent) to engine
stop solenoid.
NOTE
■
• For fastening hydraulic pipe nut, use two wrenches. Hold
the fitting with a wrench, turn the pipe nut another wrench to
avoid damage at fitting installed part.
W10125150
Cover, Side Plate and Gear
1. Secure the hydraulic pump with a vise, and remove the cover.
2. Remove the side plate (4).
3. Remove the drive gear (2) and driven gear (3) from the casing
(1).
(When reassembling)
• Take care not to damage the O-ring.
• Align the holes of the cover and casing.
• Install the side plate, noting its location and direction.
• Install the gears, noting its direction.
W10127500
Oil Seal
1. Remove the internal snap ring (2), and remove the oil seal (1).
(When reassembling)
• If the oil seal is defective, worn or scratched, replace it.
W10129650
Tightening torque
Delivery pipe nut for power
steering
65 to 75 N·m
6.6 to 7.7 kgf·m
47.9 to 55.3 ft-lbs
(1) Power Steering Delivery Pipe
(2) Accelerator Rod
(3) Suction Hose
(4) Hydraulic Pump
(5) 3-Point Hitch Delivery Pipe
(6) Engine Stop Solenoid
Tightening torque
Cover mounting screw
34.3 to 39.2 N·m
3.5 to 4.0 kgf·m
25.3 to 28.9 ft-lbs
(1) Casing
(2) Drive Gear
(3) Driven Gear
(4) Side Plate
(1) Oil Seal
(2) Internal Snap Ring
KiSC issued 11, 2006 A
Summary of Contents for B1710
