Kubota B1710 Workshop Manual Download

Page: 226 / 370

5-S3

B1710 · B2110 · B2410 · B2710, WSM

BRAKES

3. CHECKING, DISASSEMBLING AND SERVICING

[1] BRAKE PEDAL AND PARKING BRAKE

(1) Checking and Adjusting

Adjusting Brake Pedal Free Travel

CAUTION

• Stop the engine and chock the wheels before checking

brake pedal.

1. Release the parking brake.
2. Slightly depress the brake pedals and measure free travel at top

of pedal stroke.

3. If the measurement is not within the factory specifications, loosen

the lock nut and turn the turnbuckle to adjust the brake rod length.

4. Retighten the lock ut securely.

Keep the free travel in the right and left brake pedals equal.

NOTE

■

• After checking brake pedal free play, be sure to engage the

parking brake lever fully and check to see that the brake
pedals are securely locked.

W10114120

Brake pedal free travel
(L)

Factory spec.

30 to 40 mm
1.18 to 1.57 in.

(1) Brake Pedal
(2) Turnbuckle

(3) Lock Nut

KiSC issued 11, 2006 A

Summary of Contents for B1710



















































































































































































































































































































































































Search results

Summary of Contents for B1710

Reviews:

Related manuals for B1710

Brands by name

Popular brands

Kubota B1710, Workshop Manual

Search results

Summary of Contents for B1710

Reviews:

Related manuals for B1710

Brands by name

Popular brands