1-S36
B1710 · B2110 · B2410 · B2710, WSM
ENGINE
Free Length and Tilt of Valve Spring
1. Measure the free length (A) of valve spring with vernier calipers.
If the measurement is less than the allowable limit, replace it.
2. Put the valve spring on a surface plate, place a square on the
side of the valve spring.
3. Check to see if the entire side is in contact with the square.
Rotate the valve spring and measure the maximum tilt (B).
Check the entire surface of the valve spring for scratches.
If there is any defect, replace it.
W10289350
Valve Spring Setting Load
1. Place the valve spring on a tester and compress it to the same
length it is actually compressed in the engine.
2. Read the compression load on the gauge.
3. If the measurement is less than the allowable limit, replace it.
W10784360
Oil Clearance between Rocker Arm and Rocker Arm Shaft
1. Measure the rocker arm shaft O.D. with an outside micrometer.
2. Measure the rocker arm I.D. with an inside micrometer, and then
calculate the oil clearance.
3. If the oil clearance exceeds the allowable limit, replace the rocker
arm and measure the oil clearance again. If it still exceeds the
allowable limit, replace also the rocker arm shaft.
W10291500
Push Rod Alignment
1. Place the push rod on V blocks.
2. Measure the push rod alignment.
3. If the measurement exceeds the allowable limit, replace the push
rod.
W10292900
Free length (A)
Factory spec.
37.0 to 37.5 mm
1.457 to 1.456 in.
Allowable limit
36.5 mm
1.437 in.
Tilt (B)
Allowable limit
1.0 mm
0.039 in.
Setting load /
Setting length
Factory spec.
117.6 N / 31.0 mm
12.0 kgf / 31.0 mm
26.4 lbs / 1.220 in.
Allowable limit
100.0 N / 31.0 mm
10.2 kgf / 31.0 mm
22.5 lbs / 1.220 in.
Oil clearance between
rocker arm and rocker
arm shaft
Factory spec.
0.016 to 0.045 mm
0.00063 to 0.00177 in.
Allowable limit
0.10 mm
0.0039 in.
Rocker arm shaft O.D.
Factory spec.
11.973 to 11.984 mm
0.47138 to 0.47181 in.
Rocker arm I.D.
Factory spec.
12.000 to 12.018 mm
0.47244 to 0.47315 in.
Push rod alignment
Allowable limit
0.25 mm
0.0098 in.
KiSC issued 11, 2006 A
Summary of Contents for B1710
