JL-M MATERIAL SAFETY DATA SHEET
Page 1 of 1
SECTION 1 – PRODUCT IDENTIFICATION
Product Name: JL-M Lubricant
Revised:
03/07/03 Supercedes: 03/17/00
Prepared by: C. Semerod
Emergency Information: (412) 279-1149
Manufacturer’s Name: Superbolt, Inc.
Manufacturer’s Address: 1000 Gregg Street
Carnegie, PA 15106
Manufacturer’s Phone #: (412) 279-1149
SECTION 2 – HAZARDOUS INGREDIENTS
CHEMICAL NAME:
CAS
NO.: OSHA
PEL: ACGIH TLV: (STEL)
Molybdenum Disulfide
1317-33-5
10 mg/m3
10 mg/m3 N/A
Silica, Fused
60676-86-0
0.1 mg/m3 0.1 mg/m3 N/A
Graphite 7782-42-5 2 mg/m3 N/A
Silica, Crystalline 14808-60-7 0.1 mg/m3 N/A
Lubricating Oils, Petroleum,
64742-58-1
5 mg/m3*
5 mg/m3*
10mg/m3*
Hydrotreated, Spent
Residual Oils (Petroleum),
64742-62-7
5 mg/m3*
5 mg/m3*
10 mg/m3*
Solvent Dewaxed
Solvent-Refined Heavy Paraffinic
64741-88-4
5 mg/m3*
5 mg/m3*
10 mg/m3*
Distillate (Petroleum)
Solvent –Dewaxed Hydrotreated
64742-65-0
5 mg/m3*
5 mg/m3*
10 mg/m3*
Heavy Paraffinic Distillate (Petroleum)
Hydrotreated Heavy Paraffinic
64742-54-7
5 mg/m3*
5 mg/m3*
10 mg/m3*
Distillate (Petroleum)
Proprietary Additives Mixture (<1%)
(*)
Designates limits set by OSHA and the ACGIH for oil mist. This product is sold in a paste form so misting should not occur.
SECTION 3 – PHYSICAL DATA
SECTION 4 – FIRE AND EXPLOSION DATA
Appearance and Odor: Dark Grey Paste, Mild Petroleum
Boiling Point: > 500 degrees F
% Volatile: 0%
Vapor Density: > 1 (Air = 1)
Evaporation Rate: < 1 (Ether = 1)
Specific Gravity: 4.8 (Water = 1)
Vapor Pressure: Essentially 0 (mm Hg)
Solubility in Water: Insoluble
pH: N/A
Flash Point: 338 degrees F
Lower Explosive Limit: N/A
Upper Explosive Limit: N/A
Extinguishing Media: Carbon Dioxide, Regular Foam, Dry Chemical
Special Fire Fighting Procedures: Fire may produce dense smoke,
firefighters should wear self contained breathing apparatus. Use
water to cool fire exposed containers.
Unusual Fire & Explosion Hazards: Decomposition and combustion
by-products may be toxic. Heated containers may rupture or explode.
SECTION 5 – REACTIVITY DATA
SECTION 6 – STORAGE & HANDLING
Stability: Stable Hazardous Polymerization: Will not occur.
Incompatibility: Avoid contact with oxidizing agents, heat, sparks or
flame.
Hazardous Combustion By-Products: Carbon Monoxide, Sulfur
Dioxide, Aldehydes, and Nitrogen Oxides
Hazardous Decomposition: Thermal decomposition may yield
methacrylate monomers.
Handling Precautions: Use good personal hygiene practices. Clean
contaminated clothing and protective equipment before reuse.
Storage Precautions: Store in a cool dry location. Keep container
tightly closed when not in use and during transport. Keep away from
open sparks or flames.
SECTION 7 – HEALTH HAZARDS
Effects of Overexposure:
Skin: May Cause Irritation
Eyes: Eye Irritant. May cause redness and Blurred vision.
Ingestion: Not Expected
Inhalation: Not Expected (Chronic respiratory diseases may be
aggravated by dust exposure.)
NFPA CODES: Health: 1
Flammability: 1
Reactivity: 0
Carcinogenicity: Silica is a suspected carcinogen in a respirable
form by the IARC and NTP however, not by the ACIGH or OSHA.
First Aid Procedures:
Skin: Remove contaminated clothing from irritated area. Flush
exposed area with mild soap and water. Seek medical attention if
irritation persists.
Eyes: Flush eyes with large quantities of water, holding eyelids open.
Seek medical attention if irritation persists.
Ingestion: Do not induce vomiting. If spontaneous vomiting occurs,
keep head below hips to avoid aspiration into the lungs. Seek
immediate medical attention.
Inhalation: Remove to fresh air. Obtain medical attention if
necessary.
SECTION 8 – SPECIAL PROTECTION
SECTION 9 – SPILL AND DISPOSAL PROCEDURES
Eye Protection: Safety Glasses or Face Shield
Protective Gloves: Recommended
Respiratory Protection: Avoid breathing dust, use an
approved respirator if levels exceed OSHA limits.
Ventilation: Local ventilation to maintain levels within OSHA limits.
Spill Procedures: Scrape or wipe up any spilled material. Wear
proper protective equipment when cleaning up a spill.
Disposal Procedures: Dispose of in accordance with any applicable
federal, state, or local laws.
The information in this MSDS was obtained from sources which we believe are reliable. However, the information is provided without any
representation or warranty, expressed or implied, regarding the accuracy or correctness. The conditions or methods of handling, storage, use
and disposal of the product are beyond our control. For this and other reasons, we do not assume responsibility and expressly disclaim liability
for loss, damage, or expense arising out of or in any way connected with the handling, storage, use or disposal of the product.
KMT 20416125