background image

3 WORK

22

3.6

Installing the fuel tank

Danger

Fire hazard

Fuel is highly flammable.

The fuel in the fuel tank expands when warm and can escape if overfilled.

Do not fuel the vehicle in the vicinity of open flames or lit cigarettes.

Switch off the engine for refueling.

Make sure that no fuel is spilled; particularly not on hot parts of the vehicle.

If any fuel is spilled, wipe it off immediately.

Observe the specifications for refueling.

Warning

Danger of poisoning

Fuel is poisonous and a health hazard.

Avoid skin, eye and clothing contact with fuel.

Immediately consult a doctor if you swallow fuel.

Do not inhale fuel vapors.

In case of skin contact, rinse the affected area with plenty of water.

Rinse the eyes thoroughly with water, and consult a doctor in case of fuel contact with the eyes.

Change your clothing in case of fuel spills on them.

Main work

Check the throttle cable routing. (

p. 23)

E00883-11

Position the fuel tank and fit the two spoilers to the sides in
front of the radiator bracket.

Make sure that no cables or throttle cables are trapped or dam-
aged.

E00882-11

Mount and tighten screw

1

with the rubber bushing.

Guideline

Remaining screws,
chassis

M6

10 Nm (7.4 lbf ft)

(All EXC models)

Position the horn with the horn bracket.

Summary of Contents for F7303U2




















































Reviews: