KTM 250 EXC-F 2018 Setup Instructions Download Page 17

Page: 17 / 48

2 SETUP

E00489-10

–

Mount and tighten screw

with the collar bushing.

Guideline

Remaining screws,
chassis

10 Nm (7.4 lbf ft)

–

Mount and tighten screw

Guideline

Remaining screws,
chassis

10 Nm (7.4 lbf ft)

–

Mount and tighten screw

with negative cable and con-

tact disk.
Guideline

Remaining screws,
chassis

10 Nm (7.4 lbf ft)

E00498-10

–

Connect the tail light plug-in connector to the main wiring
harness plug-in connector.

–

Mount engine electronics control unit on the holder.

Info

The wiring harness runs under the engine electron-
ics control unit.

E00487-10

–

Position the main silencer. Mount screws

with the

washers, but do not tighten yet.

–

Attach spring

Spring hook (50305017000)

–

Tighten screws

Guideline

Remaining screws,
chassis

10 Nm (7.4 lbf ft)

E00494-10

–

Attach the side cover in area

and engage it in area

–

Mount and tighten screw

Guideline

Screw, sub-
frame

35 Nm (25.8 lbf ft)

Loctite

2701™

–

Mount and tighten screw

Guideline

Remaining screws,
chassis

10 Nm (7.4 lbf ft)

–

Install the battery. (

p. 28)

–

Install the fuel tank. (

p. 34)

Summary of Contents for 250 EXC-F 2018

















































Search results

Summary of Contents for 250 EXC-F 2018

Reviews:

Related manuals for 250 EXC-F 2018

Brands by name

Popular brands

KTM 250 EXC-F 2018, Setup Instructions

Search results

Summary of Contents for 250 EXC-F 2018

Reviews:

Related manuals for 250 EXC-F 2018

Brands by name

Popular brands