KSB Etanorm V Operating Manual Download Page 20 | Manualshive

Page: 20 / 62

background image

5 Installation at Site

20 of 62

Etanorm V

1228.87/01-EN

5 Installation at Site

5.1 Safety regulations

DANGER

Installing electric equipment (motors) in potentially explosive atmospheres

Risk of explosion!

▷

Comply with the applicable local explosion protection regulations.

▷

Verify the test certificate of the motor.

▷

Keep the test certificate close to the location of operation (e.g. in the foreman's
office).

5.2 Checks to be carried out prior to installation

Check the structural requirements.
The structural work required must have been prepared in accordance with the
dimensions stated in the outline drawing and/or general arrangement drawing.

5.3 Installing the pump set

Foundation

The sturdy cover plate 68-3.01 serves as a foundation on which the pump set is
fastened. This cover plate covers the tank opening completely. If the pump set is
supplied with cover plate and riser, the cover plate is supported by a sectional steel
frame provided on the tank.

If ordered without cover plate and riser, the pump set is supplied with a bolted-on
bracket 732. This bracket serves to mount the pump set on the tank.

If pump and motor are delivered separately, transport and installation can be
facilitated by screwing eyebolts into the threaded holes in the lantern for attaching
support ropes.

Installing the pump

1. Carefully align the support frame.

2. Align the base of the bracket.

3. Align the upper flange of the drive lantern with a spirit level.

4. Make adjustments between cover plate and tank edge, if required.

If the pump is installed without suction strainer, observe a minimum distance B
to the tank floor.

«
...
18
19
20
21
22
...
»

Summary of Contents for Etanorm V































































Reviews:

No comments

Related manuals for Etanorm V

Brand: Maag Pages: 16

Brand: A.O. Smith Pages: 40

Brand: Eaton Pages: 12

Brand: G&F Manufacturing Pages: 17

Brand: Calpeda Pages: 44

Brand: Calpeda Pages: 64

Brand: Calpeda Pages: 32

Brand: Balcrank Pages: 18

Altherma EKHWE150A3V3

Brand: Daikin Pages: 10

Brand: EBARA Pages: 48

Brand: OEG Pages: 28

Brand: Versamatic Pages: 18

Brand: Waterax Pages: 6

AquaMax Eco Expert 20000/12V

Brand: Oase Pages: 231

Brand: nedis Pages: 60

BREDEL 701 Series

Brand: Watson-Marlow Pages: 25

Brand: T.I.P. Pages: 117

Mainsboost Plus

Brand: Stuart Turner Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands