KSB Etanorm V Operating Manual Download Page 7

Page: 7 / 62

1 General

7 of 62

Etanorm V

1228.87/01-EN

Symbol

Description

Step-by-step instructions

Note
Recommendations and important information on how to handle
the product

1.6 Key to safety symbols/markings

Table 3:

Definition of safety symbols/markings

Symbol

Description

DANGER

DANGER

This signal word indicates a high-risk hazard which, if not avoided,
will result in death or serious injury.

WARNING

WARNING

This signal word indicates a medium-risk hazard which, if not
avoided, could result in death or serious injury.

CAUTION

CAUTION

This signal word indicates a hazard which, if not avoided, could
result in damage to the machine and its functions.

General hazard

In conjunction with one of the signal words this symbol indicates a
hazard which will or could result in death or serious injury.

Electrical hazard

In conjunction with one of the signal words this symbol indicates a
hazard involving electrical voltage and identifies information about
protection against electrical voltage.

Machine damage

In conjunction with the signal word CAUTION this symbol indicates
a hazard for the machine and its functions.

Summary of Contents for Etanorm V































































Search results

Summary of Contents for Etanorm V

Reviews:

Related manuals for Etanorm V

Brands by name

Popular brands

KSB Etanorm V, Operating Manual

Search results

Summary of Contents for Etanorm V

Reviews:

Related manuals for Etanorm V

Brands by name

Popular brands