KSB Etanorm V Operating Manual Download Page 34 | Manualshive

Page: 34 / 62

background image

7 Servicing/Maintenance

34 of 62

Etanorm V

1228.87/01-EN

7 Servicing/Maintenance

7.1 Safety regulations

The operator ensures that maintenance, inspection and installation are performed by
authorised, qualified specialist personnel who are thoroughly familiar with the
manual.

WARNING

Unintentional starting of the pump set

Risk of injury by moving components and shock currents!

▷

Ensure that the pump set cannot be started unintentionally.

▷

Always make sure the electrical connections are disconnected before carrying
out work on the pump set.

WARNING

Fluids handled, consumables and supplies which are hot and/or pose a health
hazard

Risk of injury!

▷

Observe all relevant laws.

▷

When draining the fluid take appropriate measures to protect persons and the
environment.

▷

Decontaminate pumps which handle fluids posing a health hazard.

WARNING

Insufficient stability

Risk of crushing hands and feet!

▷

During assembly/dismantling, secure the pump (set)/pump parts to prevent
tilting or tipping over.

A regular maintenance schedule will help avoid expensive repairs and contribute to
trouble-free, reliable operation of the pump, pump set and pump parts with a
minimum of servicing/maintenance expenditure and work.

NOTE

All maintenance work, service work and installation work can be carried out by KSB
Service or authorised workshops. For contact details refer to the enclosed
"Addresses" booklet or visit "

www.ksb.com/contact

" on the Internet.

Never use force when dismantling and reassembling the pump set.

7.2 Servicing/Inspection

7.2.1 Supervision of operation

CAUTION

Increased wear due to dry running

Damage to the pump set!

▷

Never operate the pump set without liquid fill.

▷

Never close the shut-off element in the suction line and/or supply line during
pump operation.

«
...
32
33
34
35
36
...
»

Summary of Contents for Etanorm V































































Reviews:

No comments

Related manuals for Etanorm V

Brand: Waterous Pages: 13

Brand: Waterous Pages: 8

Brand: Davey Pages: 12

Brand: Barmesa Pumps Pages: 42

Brand: GE Pages: 36

Brand: SAER Elettropompe Pages: 72

Brand: I.VA.CO. Pages: 12

Brand: AquaPRO Pages: 4

Brand: alkitronic Pages: 12

Brand: Becker Pages: 5

Brand: John Wood Pages: 28

Brand: Daikin Pages: 36

Brand: Bravo Pages: 12

BASITRONIC CDX 11-U

Brand: clage Pages: 32

HOTSPRING HSTB9

Brand: ZANSKAR Pages: 19

Brand: evoheat Pages: 17

Brand: Midea Pages: 13

Brand: Trane Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands