Kramer Electronics Ltd.
VW-16
– Protocol 3000
44
Function
Description
Syntax
Parameters/
Attributes
Example
FCT-MAC
Set MAC address.
To activate the
change, reset the device.
COMMAND
#FCT-MAC
mac_address
<CR>
FEEDBACK
~nn@FCT-MAC
mac_address
<CR><LF>
mac_address
– Unique MAC address.
Format: XX-XX-XX-XX-XX-XX
where X is a hex digit
Set MAC address:
#FCT-MAC
00-14-22-
01-23-45
<CR>
FCT-SN
Set serial number.
COMMAND
#FCT-SN
serial_num
<CR>
FEEDBACK
~nn@FCT-SN
serial_num
<CR><LF>
serial_num
– 14 decimal digits
Set serial number:
#FCT-SN
1976384058
1123
<CR>
HDCP-MOD
Set HDCP mode.
Set HDCP working
mode on the device input:
HDCP supported -
HDCP_ON [default].
HDCP not supported -
HDCP OFF.
HDCP support changes
following detected sink -
MIRROR OUTPUT.
When you define
3
as the
mode, the HDCP status is
defined according to the
connected output in the
following priority: OUT 1,
OUT 2. If the connected
display on OUT 2
supports HDCP, but OUT
1 does not, then HDCP is
defined as not supported.
If OUT 1 is not connected,
then HDCP is defined by
OUT 2.
COMMAND
#HDCP-MOD
in_index
,
mode
<CR>
FEEDBACK
~nn@HDCP-MOD
in_index
,
mode
<CR><LF>
in_index
– Number that indicates the
specific input:
1-N (N= the total number of inputs)
mode
– HDCP mode:
0
– HDCP Off
1
– HDCP On
2
– Follow Input
3
– HDCP defined according to the
connected output
Set the input HDCP-
MODE of IN 1 to Off:
#HDCP-MOD
1
,
0
<CR>
HDCP-MOD?
Get HDCP mode.
Set HDCP working
mode on the device input:
HDCP supported -
HDCP_ON [default].
HDCP not supported -
HDCP OFF.
HDCP support changes
following detected sink -
MIRROR OUTPUT.
COMMAND
#HDCP-MOD?
in_index
<CR>
FEEDBACK
~nn@HDCP-MOD
in_index
,
mode
<CR><LF>
in_index
– Number that indicates the
specific input:
1-N (N= the total number of inputs)
mode
– HDCP mode:
0
– HDCP Off
1
– HDCP On
2
– Follow Input
3
– HDCP defined according to the
connected output
Get the input
HDCP-MODE of IN 1
HDMI:
#HDCP-MOD?
1
<CR>
HDCP-STAT?
Get HDCP signal status.
io_mode =1
– get the
HDCP signal status of the
sink device connected to
the specified output.
io_mode =0
– get the
HDCP signal status of the
source device connected
to the specified input.
COMMAND
#HDCP-STAT?
io_mode
,
in_index
<CR>
FEEDBACK
~nn@HDCP-STAT
io_mode
,
in_index
,
status
<CR><LF>
io_mode
– Input/Output
0
– Input
1
– Output
io_index
– Number that indicates the
specific number of inputs or outputs
(based on io_mode):
1-N (N=total number of inputs or
outputs)
status
– Signal encryption status -
valid values On/Off
0
– HDCP Off
1
– HDCP On
Get the output HDCP-
STATUS of IN 1:
#HDCP-
STAT?
0
,
1
<CR>
HELP
Get command list or help
for specific command.
COMMAND
#HELP
<CR>
#HELP
cmd_name
<CR>
FEEDBACK
1. Multi-line:
~nn@Device
cmd_name
,
cmd_name…
<CR><LF>
To get help for command use: HELP (COMMAND_NAME)
<CR><LF>
~nn@HELP
cmd_name:
<CR><LF>
description
<CR><LF>
USAGE:usage
<CR><LF>
cmd_name
– Name of a specific
command
Get the command list:
#HELP
<CR>
To get help for
AV-SW-TIMEOUT:
#HELP
av-sw-timeou
t
<CR>
IDV
Set visual indication from
device.
Using this command,
some devices can light a
sequence of buttons or
LEDs to allow
identification of a specific
device from similar
devices.
COMMAND
#IDV
<CR>
FEEDBACK
~nn@IDV
ok
<CR><LF>
#IDV
<CR>
IMAGE-PROP
Set the image size.
Sets the image
properties of the selected
scaler.
COMMAND
#IMAGE-PROP
scaler_id
<CR>
FEEDBACK
~nn@IMAGE-PROP
scaler_id
,
video_mode…
<CR><LF>
scaler_id
– Scaler number –
1
– Scaler1
2
– Scaler2
video_mode
– Status
0
– Video enabled
1
– Video disabled
2
– Blank picture
Set the image size:
#IMAGE-PROP
1
<CR>