Korenix JetNet 5008G-P Series User Manual Download | Manualshive

Page: 29 / 96

background image

26

new firmware. Please remind the attached users before you do this.

Figure 4.2.5.1 Main UI of Firmware Upgrade

There are 2 modes for users to backup/restore the configuration file, Local File mode and
TFTP Server mode.

Local File

mode: In this mode, the switch acts as the file server. Users can browse the

target folder and then type the file name to backup the configuration. Users also can
browse the target folder and select the existed configuration file to restore the
configuration back to the switch. This mode is only provided by Web UI while CLI is not
supported.

TFTP Server

mode: In this mode, the switch acts as the TFTP client. Before you do so,

make sure that your TFTP server is ready. And then please type the IP address of TFTP
Server IP address. This mode can be used in both CLI and Web UI.

TFTP Server IP Address

: You need to key in the IP address of your TFTP Server here.

Firmware File Name

: The file name of the new firmware.

The UI also shows you the latest firmware version and built date. Please check the version
number after the switch is rebooted.

Figure 4.2.6.2 Firmware Upgrade - Local File mode.

«
...
27
28
29
30
31
...
»

Summary of Contents for JetNet 5008G-P Series

































































































Reviews:

No comments

Related manuals for JetNet 5008G-P Series

Elinx EIRP305-T

Brand: B&B Electronics Pages: 19

Brand: Q-See Pages: 2

Brand: Netopia Pages: 38

Brand: Vivotek Pages: 170

Brand: Garland Pages: 43

NSLU2 - Network Storage Link NAS Server

Brand: Linksys Pages: 64

Brand: TRENDnet Pages: 62

Brand: XtendLan Pages: 228

Brand: Baicells Pages: 10

Brand: IDT Pages: 207

Brand: IBM Pages: 34

Brand: Digisol Pages: 22

Brand: Ubiquiti Pages: 23

Brand: MA lighting Pages: 49

Brand: DHD Power Cruiser Pages: 60

SecPath F50X0 Series

Brand: H3C Pages: 41

Q-SYS QIO-GP8x8

Brand: QSC Pages: 13

TeleLite 720920 Series

Brand: Positron Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands