Korenix JetNet 5008G-P Series User Manual Download | Manualshive

Page: 87 / 96

background image

84

Port Statistics

Port Statistics

JetNet 5008G-P# show rmon statistics fa4 (select interface)

Interface fastethernet4 is enable connected, which has

Inbound:
      Good Octets: 178792, Bad Octets: 0
      Unicast: 598, Broadcast: 1764, Multicast: 160
      Pause: 0, Undersize: 0, Fragments: 0
      Oversize: 0, Jabbers: 0, Disacrds: 0
      Filtered: 0, RxError: 0, FCSError: 0
Outbound:
Good Octets: 330500
      Unicast: 602, Broadcast: 1, Multicast: 2261
      Pause: 0, Deferred: 0, Collisions: 0
SingleCollision: 0, MultipleCollision: 0
ExcessiveCollision: 0, LateCollision: 0
Filtered: 0, FCSError: 0

Number of frames received and transmitted with a length of:

64: 2388, 65to127: 142, 128to255: 11
256to511: 64, 512to1023: 10, 1024toMaxSize: 42

Port Mirroring

Enable Port Mirror

JetNet 5008G-P(config)# mirror en
Mirror set enable ok.

Disable Port Mirror

JetNet 5008G-P(config)# mirror disable
Mirror set disable ok.

Select Source Port

JetNet 5008G-P(config)# mirror source fa1-2

both Received and transmitted traffic
rx Received traffic
tx Transmitted traffic

JetNet 5008G-P(config)# mirror source fa1-2 both
Mirror source fa1-2 both set ok.

Note: Select source port list and TX/RX/Both mode.

Select Destination Port JetNet 5008G-P(config)# mirror destination fa6 both

Mirror destination fa6 both set ok

Display

JetNet 5008G-P# show mirror

Mirror Status : Enabled
Ingress Monitor Destination Port: fa6
Egress Monitor Destination Port: fa6
Ingress Source Ports :fa1,fa2,
Egress Source Ports :fa1,fa2,

Event Log

Display

JetNet 5008G-P# show event-log

<1>Jan    1 02:50:47 snmpd[101]: Event: Link 4 Down.
<2>Jan    1 02:50:50 snmpd[101]: Event: Link 5 Up.
<3>Jan    1 02:50:51 snmpd[101]: Event: Link 5 Down.
<4>Jan    1 02:50:53 snmpd[101]: Event: Link 4 Up.

Ping

Ping IP

JetNet 5008G-P# ping 192.168.10.33

PING 192.168.10.33 (192.168.10.33): 56 data bytes
64 bytes from 192.168.10.33: icmp_seq=0 ttl=128 time=0.0 ms
64 bytes from 192.168.10.33: icmp_seq=1 ttl=128 time=0.0 ms
64 bytes from 192.168.10.33: icmp_seq=2 ttl=128 time=0.0 ms
64 bytes from 192.168.10.33: icmp_seq=3 ttl=128 time=0.0 ms
64 bytes from 192.168.10.33: icmp_seq=4 ttl=128 time=0.0 ms

--- 192.168.10.33 ping statistics ---
5 packets transmitted, 5 packets received, 0% packet loss
round-trip min/avg/max = 0.0/0.0/0.0 ms

«
...
85
86
87
88
89
...
»

Summary of Contents for JetNet 5008G-P Series

































































































Reviews:

No comments

Related manuals for JetNet 5008G-P Series

IES615-2D Series

Brand: 3onedata Pages: 3

Brand: 3One data Pages: 5

Brand: 3onedata Pages: 33

Brand: M2M Pages: 9

BladeCenter Management Module

Brand: IBM Pages: 184

RealPort Ethernet 10/100

Brand: Xircom Pages: 30

Brand: Tektronix Pages: 178

Brand: TRENDnet Pages: 10

Turbo NAS TVS-71 Series

Brand: QNAP Pages: 51

Brand: VCS Pages: 118

Brand: Observint Pages: 117

Brand: Valcom Pages: 4

GS2020E GigaSPIRE BLAST

Brand: Calix Pages: 15

Brand: ALIBI Pages: 232

TeleLite 720920 Series

Brand: Positron Pages: 21

SmartNode 4634 Series

Brand: Patton electronics Pages: 12

Brand: TP-Link Pages: 2

Network Video Recorder

Brand: IC Realtime Pages: 118

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands