Korenix JetNet 5008G-P Series User Manual Download | Manualshive

Page: 82 / 96

background image

79

4.11 Monitor and Diag

JetNet 5008G-P provides several types of features for you to monitor the status of the
switch or diagnostic for you to check the problem when encountering problems related to
the switch. The features include MAC Address Table, Port Statistics, Port Mirror, Event
Log and Ping.

Following commands are included in this group:

4.10.1 MAC Address Table

4.10.2 Port Statistics

4.10.3 Port Mirror

4.10.4 Event Log

4.10.5 Ping

4.11.1 MAC

Address Table

JetNet 5008G-P provides 8K entries in MAC Address Table. In this page, users can
change the Aging time, add Static Unicast MAC Address, monitor the MAC address or sort
them by different packet types and ports. Click on

Apply

to change the value.

Aging Time (Sec)

Each switch fabric has limit size to write the learnt MAC address. To save more entries for
new MAC address, the switch fabric will age out non-used MAC address entry per Aging
Time timeout. The default Aging Time is 300 seconds. The Aging Time can be modified in
this page.

Static Unicast MAC Address

In some applications, users may need to type in the static Unicast MAC address to its MAC
address table. In this page, you can type MAC Address (format: xxxx.xxxx.xxxx), select its
VID and Port ID, and then click on

Add

to add it to MAC Address table.

MAC Address Table

In this MAC Address Table, you can see all the MAC Addresses learnt by the switch fabric.
The packet types include Management Unicast, Static Unicast, Dynamic Unicast, Static
Multicast and Dynamic Multicast. The table allows users to sort the address by the packet
types and port.

Packet Types:

Management Unicast

means MAC address of the switch. It belongs to

CPU port only.

Static Unicast

MAC address can be added and deleted.

Dynamic Unicast

MAC is MAC address learnt by the switch Fabric.

Static Multicast

can be added by CLI

and can be deleted by Web and CLI.

Dynamic Multicast

will appear after you enabled

IGMP and the switch learnt IGMP report.

Click on

Remove

to remove the static Unicast/Multicast MAC address. Click on

Reload

to

refresh the table. New learnt Unicast/Multicast MAC address will be updated to MAC
address table.

«
...
80
81
82
83
84
...
»

Summary of Contents for JetNet 5008G-P Series

































































































Reviews:

No comments

Related manuals for JetNet 5008G-P Series

Brand: Abocom Pages: 11

Brand: Abocom Pages: 19

Brand: H3C Pages: 22

Brand: H3C Pages: 3

Brand: National Instruments Pages: 162

Brand: Queclink Pages: 9

Brand: NETGEAR Pages: 14

Brand: 1&1 Pages: 32

WNFB-265AXI(BT)

Brand: Sparklan Pages: 14

Brand: Avaya Pages: 73

Brand: Airlink101 Pages: 46

Brand: Supermicro Pages: 15

Brand: Tripp Lite Pages: 2

Brand: Paradyne Pages: 74

Brand: NetComm Pages: 75

Brand: Proscend Pages: 93

Brand: Me Pages: 28

Brand: Tripp Lite Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands