Kongskilde GMT 3205 L P Operator'S Manual Download Page 52 | Manualshive

Page: 52 / 190

background image

4 - OPERATING INSTRUCTIONS

Check before use

Before you operate the disc mower-conditioner for the first
time, perform the following items:

• Read this operator's manual carefully; especially the

chapter headed ”Safety information”.

• Check the correct assemblage of the implement. Also

check that the implement is undamaged.

• Check that no parts have been tied up inside the imple-

ment in connection with the delivery of the implement.

• Check that the protection (guards and canvases) on the

implement are complete, intact and correctly mounted,
and that the side guards are folded down. Canvases
and shields secure against ejection of stones and for-
eign matter.

• Check the revolving parts (blades, blade bolts, discs

and flow caps). Replace damaged, worn or missing
parts immediately.

• Check the correct installation of the discs and the

blades.

• Check the correct installation of the safety devices.

Also check if the safety devices are intact.

• Remove all the tools from the implement, including the

quick-change blade tool.

• Check that the Power Take-Off (PTO) speed of the im-

plement (and of the tractor) is correct. Too high PTO
speed can be dangerous. Too low PTO speed causes
bad cutting, blocking of the disc mower and high torque
on the drive shafts.

• Make sure that the tractor is capable of maintaining the

specified

1000 RPM

with no load on the implement.

• Check the length of the primary PTO shaft. If the PTO

shafts is too short or too long it may damage the trac-
tor as well as the implement considerably. Check that
the protection tubes do not get jammed or damaged in
any position. Secure the safety chains of the protection
tubes properly. Check that the safety chains do not in
any position get too tight or damaged.

4-2

«
...
50
51
52
53
54
...
»

Summary of Contents for GMT 3205 L P































































































































































































Reviews:

No comments

Related manuals for GMT 3205 L P

Brand: Backyard Discovery Pages: 51

Brand: Nautilus Pages: 12

Brand: CAIRE Pages: 16

FreeStyle Comfort

Brand: CAIRE Pages: 33

Brand: Mandam Pages: 9

Brand: Gardol Pages: 260

Brand: York Fitness Pages: 20

Brand: Quark-Elec Pages: 2

LSP400 LED Series

Brand: WE-EF Pages: 6

Brand: Hoist Fitness Pages: 17

Brand: Peak Pilates Pages: 4

Brand: Toro Pages: 12

Brand: Bowa Pages: 140

Brand: Toparc Pages: 32

Serious Steel 805106

Brand: ParaBody Pages: 6

Z33-D060.02 S2A

Brand: Jäger Pages: 36

Royal Squat Rack SX-5 II

Brand: KingsBox Pages: 5

Brand: TOPMAQ Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands