Kongskilde GMT 3205 L P Operator'S Manual Download Page 27 | Manualshive

Page: 27 / 190

background image

2 - SAFETY INFORMATION

Drive at a safe speed to ensure control and ability to stop
in an emergency.

Lock the tractor brake pedals together. Never use inde-
pendent breaking at transport speeds.

Trailed implements and ballast weights influence the driv-
ing, steering and braking capacity of the tractor. Make
sure that the additional weight of the implement on the
linkage does not compromise driving, steering and brak-
ing capacity of the tractor. Install front weights or repair
the brakes if the tractor is not safe to drive.

Reduce speed during turns. Tractors have not been de-
signed for fast turning. Avoid that the rear end of the im-
plement hits an obstacle.

When you turn during transport, pay attention to the over-
hang and/or oscillating weight of the implement.

Use engine braking when you drive down hills. Do not
coast.

Watch for obstructions, particularly if over-width. Observe
any load ratings applicable on bridges.

After you finish the transport, before you leave the tractor,
always lower the implement to the ground in parking po-
sition, turn off the tractor engine, pull the parking brake,
and remove the key from the ignition.

2-7

«
...
25
26
27
28
29
...
»

Summary of Contents for GMT 3205 L P































































































































































































Reviews:

No comments

Related manuals for GMT 3205 L P

Brand: JB Systems Pages: 12

Brand: GALBIATI Pages: 20

Brand: Unitary products group Pages: 28

Brand: MAHA Pages: 21

Brand: MAGUIRE Pages: 47

Brand: Octane Fitness Pages: 20

Brand: Oceaneering Pages: 27

Brand: QRS Pages: 16

Brand: QMAXZ Lighting Pages: 36

Brand: Waterpik Pages: 2

Brand: WaterUps Pages: 2

Brand: Yamaha Pages: 4

Brand: Wacker Neuson Pages: 120

Brand: GE Pages: 176

Brand: Triton Blue Pages: 11

TUV COMFORT LIGHT Series

Brand: olympia electronics Pages: 4

Brand: Grange Pages: 2

Dual-Lite EVHC-BC Series

Brand: Hubbell Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands