Kongsberg M3 Sonar Reference Manual Download

Page: 35 / 182

922-20297001/1.2

Choosing the sonar range

The

Range

function allows you to specify the maximum theoretical vertical depth and

horizontal distance covered by the M3 Sonar FLS.

Context

The M3 Sonar FLS Sonar Head can operate at different predefined near and far
ranges.

The range value is defined from the Sonar Head.

Note

You cannot change the range until the Sonar Head is connected. Right-clicking
in the sonar view and the range slider bar will both be disabled until the sonar
is running.

Procedure

Click

Setup

→

Connect

to start the Sonar Head.

Right-click inside the sonar view to display the range menu.

Select the desired near and far range from the menu.

Tip

You can change the units of measurement in the

Preferences

dialog box.

You can increase or decrease the range using the range slider bar to the
left of the sonar view.

Click the top arrows to increase or decrease the far range.

Operating procedures

Summary of Contents for M3 Sonar























































































































































































Search results

Summary of Contents for M3 Sonar

Reviews:

Related manuals for M3 Sonar

Brands by name

Popular brands

Kongsberg M3 Sonar, Reference Manual

Search results

Summary of Contents for M3 Sonar

Reviews:

Related manuals for M3 Sonar

Brands by name

Popular brands