Kongsberg M3 Sonar Reference Manual Download

Page: 25 / 182

922-20297001/1.2

Procedure

Click

Setup

→

Connect

to start the Sonar Head.

Make sure that a sonar image appears in the sonar view window.

Click the “i” icon in the top-left corner of the sonar view to open the

Information Widget

Make sure that the sensor data is updating in the

Information Widget

Make sure that no errors are displayed in the

Output

Messages

window.

Click

Display

→

Output Messages Window

Make sure there are no errors shown in the

Output

Messages

window under the

Host Messages

Head

Messages

tab.

Make sure there are no errors in the

Connection Status

and

Head Status

windows.

Click on the text “Active” located in the
lower-right corner of the status bar.

Observe that the

Connection Status

window opens.

Make sure that all items listed under the M3 Sonar FLSSonar show check marks.

If any items are shown with an “X” in a red circle, it usually means the device has
failed to connect. Disconnect and make sure that no sensors have failed.

Getting started

Summary of Contents for M3 Sonar























































































































































































Search results

Summary of Contents for M3 Sonar

Reviews:

Related manuals for M3 Sonar

Brands by name

Popular brands

Kongsberg M3 Sonar, Reference Manual

Search results

Summary of Contents for M3 Sonar

Reviews:

Related manuals for M3 Sonar

Brands by name

Popular brands